Gree GEH09AA-K6DNA1F/I El Manual Del Propietario página 14

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

How to use the remote control to operate the unit
6
SWING:
Press this button to set up &down swing angle, which circularly changes as below:
This remote controller is universal . If any command
out the command as
indicates the guide louver swings as:
7
I FEEL:
Press this button to turn on I FEEL function. The unit automatically adjust temperature according to
the sensed temperature. Press this button again to cancel I FEEL function.
When I FEEL function is turned on, the remote controller should be put within the area where indoor unit
can receive the signal sent by the remote controller.
8
/
P
ress this button to achieve the on and off of healthy and scavenging functions in operation status.
Press this button for the first time to start scavenging function;
LCD displays"
". Press the button for the second time to start healthy and scavenging functions
simultaneously; LCD displays"
and scavenging functions simultaneously. Press the button for the fourth time to start healthy
function; LCD display "
NOTE: This function is applicable to partial of models.
SLEEP:
9
Press this button, can select Sleep 1 (
circulate between these, after electrified, Sleep Cancel is defaulted.
Sleep 1 is Sleep mode 1, in Cool mode: sleep status after run for one hour, the main
unit setting temperature will increase 1
setting temperature; In Heat mode: sleep status after run for one hour, the setting temperature will
decrease 1 ℃, 2 hours, setting temperature will decrease 2 ℃, then the unit will run at this setting
temperature.
Sleep 2 is sleep mode 2, that is air conditioner will run according to the presetting a group of sleep temperature curve.
Sleep 3- the sleep curve setting under Sleep mode by DIY:
(1) Under Sleep 3 mode, press "Turbo" button for a long time, remote control enters into user individuation sleep
setting status, at this time, the time of remote control will display "1 hour ", the setting temperature "88" will
display the corresponding temperature of last setting sleep curve and blink (The first entering will display
according to the initial curve setting value of original factory);
(2) Adjust "+" and "-" button, could change the corresponding setting temperature, after adjusted, press
"Trubo "button for confirmation;
(3) At this time, 1 hour will be automatically increased at the timer postion on the remote control, (that are
"2 hours " or "3 hours " or "8 hours "), the place of setting temperature "88" will display the
corresponding temperature of last setting sleep curve and blink;
(4) Repeat the above step (2) ~ (3) operation, until 8 hours temperature setting finished, sleep
curve setting finished, at this time, the remote control will resume the original timer display;
temperature display will resume to original setting temperature.
Sleep3- the sleep curve setting under SLEEP mode by DIY could be inquired:
The user could accord to sleep curve setting method to inquire the presetting sleep curve, enter into user
individuation sleep setting status, but do not change the temperature, press "Turbo" button directly for confirmation.
Note: In the above presetting or enquiry procedure, if continuously within10s, there is no button pressed, the
sleep curve setting within10s, there is no button pressed, the sleep curve setting status will be automatically
quit and resume to display the original displaying. In the presetting or enquiry procedure, press "ON/OFF"
button, "Mode" button, "Timer"button or "Sleep" button, the sleep curve setting or enquiry status will quit similarly.
OFF
" and "
" . Press this button for the third time to quit healthy
" . Press this button again to repeat the operation above.
), Sleep 2 (
℃,setting temperature increased 2℃, the unit will run at this
,
or
is sent out, the unit will carry
),Sleep 3 (
10
OPERATION INSTRUCTIONS
) and cancel the Sleep,

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Geh12aa-k6dna1a/iGeh18aa-k6dna1f/i

Tabla de contenido