In-Line Maintenance Heater (Whirlpool Models Only); High-Limit Switch; Cleaning; Maintenance - Jacuzzi PRIMÓ Manual De Instalación

Primó™ Collection

In-Line Maintenance Heater (Whirlpool models only)

The heater turns ON automatically any time whirlpool operation is
active. Heater operation is not displayed on the control panel. There
is a visible indicator light on the heater itself that signifies the heater
is operating. The heater will help maintain the temperature of the
water in the bathtub (Figure 15).
Vacuum Switch
The heater is equipped with a preset vacuum switch which will
not allow the heater to turn ON if the pump is not running and
water is not flowing through the whirlpool system.

High-Limit Switch

The heater includes an exclusive High-Limit switch. This safety circuit will not false trip from hot tap water. It will only turn OFF the
heater if the thermostat fails. To reset, press the button. If the high-limit trips frequently, please contact us at www.jacuzzi.com, or at
1-800-288-4002.

Cleaning

Do not use oil or oil-based bathtub additives. Never use abrasive, or caustic, household cleaners
CAUTION
on any Jacuzzi Luxury Bath product.
If you want to use any kind of bathtub additive, use only a small amount of low-foaming powder or crystal substance; the whirlpool
action intensifies the foaming properties of soaps.
The use of certain bathtub oils, bubble baths, and bathtub additives may increase the level of accumulations of bathtub residue
in the whirlpool system and may cause false reading of the water level sensors. If excess accumulations persist, you should
discontinue use of these products.
To remove accumulations of bathtub residue from the whirlpool system, it is recommended that a bathtub be cleaned regularly. For
best results, however, we recommend that you clean your whirlpool bathtub after each use using Systems Clean™, our exclusive
two-part plumbing system cleaner made specifically for whirlpool bathtubs. Systems Clean™ is available through an authorized
Jacuzzi Luxury Bath Distributor or by calling us direct at 1-800-288-4002 or may be purchased online at www.jacuzzi.com.

Maintenance

To clean your bathtub, simply use a mild, nonabrasive liquid detergent solution. You can protect and restore the gloss to a dulled
acrylic surface by applying Meguiar's #10 Mirror Glaze, a product specifically designed for use on acrylic finishes. If Meguiar's is not
available, use a fine grade automotive rubbing compound followed by an application of clear automotive paste wax.
Minor scratches which do not penetrate the color finish can be removed by lightly sanding with 600-grit wet/dry sandpaper. Restore
the gloss using Meguiar's Mirror Glaze or automotive paste wax. Major scratches and gouges which penetrate the acrylic surface will
require refinishing. Call Jacuzzi Luxury Bath to find a service agent in your area.
Whirlpool Suction Cover/Strainer
Maintenance
Clean the whirlpool suction cover/strainer of hair and debris when
necessary (Figure 16).
Remove the center screw and detach the suction cover.
1
Clean the cover by backflushing debris from the holes.
2
Replace the suction cover immediately after cleaning.
3
WARNING
Keep hair a minimum of 6 inches (152 mm) away from the suction
fitting at all times when the whirlpool system is operating. Hair longer
than shoulder length should be secured close to the head, or a bathing
cap should be worn.
Do not operate the whirlpool system with the suction cover/strainer
removed! It is a safety device and must always be in place on the
suction fitting to minimize the potential hazard of hair and body
entrapment.
Installation and Operation
OVER HEAT
PROTECTION
PUSH TO RESE T
Screw
www.jacuzzi.com
High Limit Reset
HEATER ON
Suction Fitting
Suction Cover
Fig. 15
Heater On
Fig. 16
Page 11