mundoclima MVD DC2 Manual De Instalación Y Usuario página 36

Figure 6.3: Models 400 / 450
450
400
350
300
250
200
150
100
50
0
4300 4800
Figure 6.4: Model 560
425
375
325
275
225
175
125
75
25
4950 5450
Set proper external static pressure (ESP) according to the actual installation
conditions. Otherwise it may cause some problems.
If the connecting duct is long and the ESP setting is small, the airflow will be
very small, leading to poor performance.
If the connecting duct is short and the ESP setting is large, the airflow will be
very large, leading to higher operating noise and even water may be blown
out through the air outlet.
ESP can be set through the DIP switch SW2 on the main board or the new
wired controller. Please refer to Part "7.3 DIP switch settings on main board"
for SW2 setting or the wired controller manual for wired controller setting.
Four ESP can be set through DIP switch SW2.
Capacity
ESP1
16.0kW 100Pa
20.0-28.0kW 170Pa
40-56kW 300Pa
Twenty ESP can be set through the new wired controller.
00 01 02 03
Capacity
16kW 30Pa 50Pa 60Pa 70Pa
20-28kW 30Pa 50Pa 60Pa 70Pa
40-56kW 100Pa 120Pa 140Pa 160Pa 180Pa 200Pa 220Pa 240Pa 260Pa 270Pa
10 11 12 13
Capacity
16kW 140Pa 150Pa 160Pa 170Pa 180Pa 190Pa 200Pa 200Pa 200Pa 200Pa
20-28kW 140Pa 150Pa 160Pa 170Pa 180Pa 190Pa 200Pa 210Pa 230Pa 250Pa
280Pa 290Pa 300Pa 310Pa 320Pa 330Pa 340Pa 360Pa 380Pa 400Pa
40-56kW
5300
5950 6450
Air flow (m /h)
3
ESP2 ESP3 ESP4
50Pa 170Pa 200Pa
100Pa 200Pa 250Pa
100Pa 200Pa 400Pa
04 05 06 07 08
80Pa 90Pa 100Pa 110Pa 120Pa 130Pa
80Pa 90Pa 100Pa 110Pa 120Pa 130Pa
14 15 16 17 18
5800 6300
Air flow (m 3 /h)
6950
Selection instructions for static pressure set through the wired
controller
1) The IDU static pressure can be set using the wired controller
ZLWK WKH VWDWLF SUHVVXUH VHWWLQJV IXQFWLRQ
2) Hold the "Function" button + "Mode" button for 5s to enter the
parameter settings interface (the unit must be off);
3) After accessing the parameter settings interface, the tempera-
WXUH DUHD GLVSOD\V &  3UHVV WKH
switch parameter code. After "C9" is selected, press the "OK"
EXWWRQ WR DFFHVV WKH SDUDPHWHU VHWWLQJV LQWHUIDFH 3UHVV WKH
DQG EXWWRQV WR DGMXVW WKH SDUDPHWHU YDOXH WKH IROORZLQJ
table provides the corresponding static pressures of the values).
Press "OK" to save the parameters and complete the parameter
settings.
4) Press "Cancel" to return to the previous layer until exiting the
parameter settings, or exit the parameter settings when there
DUH QR RSHUDWLRQV DIWHU V
5) On the parameter settings interface, the wired controller does
not respond to the remote control signal. The wired controller
does not respond to the APP remote control signal.
09
6)The "Mode", "Fan Speed", "Swing", "Function" and "On/Off"
buttons are invalid on the parameter settings interface.
19
34
400Pa
380Pa
360Pa
340Pa
300Pa(default)
280Pa
250Pa
220Pa
190Pa
160Pa
130Pa
100Pa
6800
400Pa
380Pa
360Pa
340Pa
330Pa
320Pa
310Pa
300Pa(default)
290Pa
280Pa
270Pa
260Pa
240Pa
220Pa
200Pa
180Pa
160Pa
140Pa
120Pa
100Pa
7450 7950
(ex. WDC-120GWK)
DQG EXWWRQV WR
7300