Cramer 1400286 Manual De Instrucciones página 4

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 15
EN
DE ES IT FR PT NL RU FI SV NO DA PL CS SK SL HR HU RO BG EL AR TR HE LT LV ET
For complete charging instructions, refer to the
Operator's Manuals for your battery pack and charger
models.
NOTE: To avoid serious personal injury, always remove
the battery pack and keep hands clear of the lock-out
button when carrying or transporting the tool.
Do not allow familiarity with this product to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict serious injury.
Always wear safety goggles or safety glasses with
side shields when operating power tools. Failure to
do so could result in objects being thrown into your
eyes, resulting in possible serious injury.
Do not use any attachments or accessories not
recommended by the manufacturer of this product.
The use of attachments or accessories not
recommended can result in serious personal injury.
ADDING BAR AND CHAIN LUBRICANT
See figure 13.
Use Bar and Chain Lubricant. It is designed for chains
and chain oilers, and is formulated to perform over a
wide temperature range with no dilution required.
NOTE: Pole saw comes from the factory with no bar and
chain lubricant added. Level should also be checked
after every 20 minutes of use and refilled as needed.
„ Unscrew and remove the cap from the oil tank.
„ Pour oil in the tank and monitor the level on the
indicator.
„ Make sure no impurities penetrate the oil tank when
filling.
„ Screw on the oil cap and tighten it.
NOTE: Do not use dirty, used or otherwise contaminated
oils. Damage may occur to the bar or chain.
NOTE: It is normal for oil to seep from the saw when
not in use. To prevent seepage, empty the oil tank after
each use then run for one minute. When storing the unit
for a long period of time (three months or longer) be
sure the chain is lightly lubricated; this will prevent rust
on the chain and bar sprocket.
English (Original instructions)
WARNING
WARNING
WARNING
INSERTING AND REMOVING THE BATTERY
See figure 14.
„ To insert the battery, line it up with the battery
compartment on the tool. Slide the battery into the
battery compartment and push until the battery
snaps into place.
„ To remove the battery, push the release button. This
will cause the battery to raise out of the tool. Then
pull the battery out of the battery compartment.
PREPARATION FOR CUTTING
„ Wear non-slip gloves for maximum grip and
protection.
„ Maintain a proper grip on the unit whenever the
motor is running. Use your right hand to firmly grip
the rear handle while your left hand has a firm grip
on the pole shaft.
„ Hold unit firmly with both hands. Always keep your
left hand on the pole shaft and your right hand on
the rear handle, so your body is to the left of the
chain line. Never use a left-handed (cross-handed)
grip, or any stance that places your body or arm
across the chain line.
„ Never stand directly under the limb you are cutting.
„ Be certain the collars are fully tightened before
operating equipment; check them periodically for
tightness during use to avoid serious injury.
TURNING THE TOOL ON AND OFF
See figure 15.
For your safety, this tool is equipped with a double
switching system. This system prevents starting the
tool inadvertently.
Switching on
„ Press the lock-out button (4) using your thumb and
at the same time squeeze the trigger (3).
„ Release the lock-out button (4).
Switching off
„ Release the trigger (3). Upon release of the trigger
(3), the trigger lock (4) will automatically reset to the
locked position.
WORK TECHNIQUES
Delimbing a tree
See figure 16.
Make sure there is nothing or nobody in the area
where the branches will fall.
„ Stand opposite the branch you want to cut.
3
WARNING

Publicidad

Tabla de contenido
loading

Tabla de contenido