Publicidad
Idiomas disponibles
Idiomas disponibles
WARNING:
Ensure the electricity is turned OFF at the main
switch board before wiring to connector. All work on cable,
pressure chamber and motor should only be carried out
by a qualified Saniflo servicing agent, as special tools are
required.
7
START-UP AND PROGRAMMING
7a
START-UP
Plug in the power socket. Wait 20 seconds: appliance
initializing. Open the water tap to rinse well. Start the
normal flush by pressing the dark grey section of the
flush button. Put a few sheets of toilet paper down in the
bowl and flush again.
Wash basin option: turn on the washbasin tap, and the
motor will activate automatically. Check the watertightness
of all connections.
Note:
the basin tap should be watertight. Any dripping will
cause the motor to activate in regular short bursts.
7b
PROGRAMMING
The length of your SANICOMPACT
according to which cycle you choose.
Eco flush (by default, light grey button):
19 seconds and 3.8L: rinsing of the bowl for 10 seconds,
the pump works for 7 seconds (for 7 seconds, the bowl
continues to fill), then the bowl fills again for 2 seconds.
You can lengthen the first rinse of the eco flush to 16
seconds if the default flush is not enough.
Normal flush (dark grey button):
25 seconds and 5L: The bowl is rinsed for 16 seconds,
the pump works for 7 seconds (for 7 seconds, the bowl
continues to fill) then the bowl fills again for 2 seconds.
To re-programme:
• Hold the ECO button (light grey button) down for 5
seconds.
• The motor works for 2 seconds, this means you have
entered programming mode.
• Each time you press the dark grey button you increase
the length of the ECO flush by 1 second: each time
you press it will be validated by the motor running for
a short period.
• Each time you press the grey button you decrease the
length of the flush by 1 second: each time you press it
will be validated by the motor running for a short period.
To exit programming mode:
• Wait for 5 seconds without pressing any buttons.
The motor runs for 2 seconds, this means that you have
left programming mode.
Comment 1: the minimum length of the first rinsing flush
for the normal flush is 19 seconds (default programming)
and the maximum length is 25 seconds.
Comment 2: the normal flush cannot be modified.
8
USE
SANICOMPACT
®
/SANICERAMIC
special maintenance.
WARNING 1:
The SANICOMPACT
range should only be used for the evacuating of normal
human waste, toilet paper and household WC clean-
sers.
Damage may occur to the machine if the following are
disposed of via the WC; Cotton wool, tampons, sanitary
towels, wet wipes, kitchen towels, condoms as well as
other fabric or hard objects. Solvents, acids and other
chemicals can also cause damage to the unit, and will
invalidate the warranty.
WARNING 2:
In case of a long electrical shut off (vacation,
strike, work being done on the electrical or water supply)
close the water supply.
/SANICERAMIC
's flush varies
®
®
®
does not require any
/SANICERAMIC
®
®
9
CLEANING AND REMOVAL OF SCALE
• To clean the bowl and remove scale, use regular
bathroom cleaning products.
• To avoid accumulations of scale inside the motor,
we advise you to clean it regularly. To do so:
• Shut off the water supply
• Flush the toilet
• Pour one litre of bathroom cleaning product
(or vinegar) in the bowl
• Leave sit for a few hours
• Open water supply and flush
• the toilet several times.
The frequency of the cleaning depends on the hardness of
the water in your area. We advise you to do it at least once
a year.
Do not put any acids, caustic sodas or solvents down
SANICOMPACT
®
/SANICERAMIC
10
REMOVAL
ALL WORK INVOLVING DISMANTLING OF THE APPLIANCE
MUST BE CARRIED OUT BY AN APPROVED REPAIR AGENT
ANY SERVICE WORK INVOLVING ELECTRICAL COMPONENTS SHOULD ONLY BE CARRIED OUT
BY A RECOGNISED SERVICE ENGINEER
11
GUARANTEE
The SANICOMPACT
®
/SANICERAMIC
subject to correct installation and usage.
®
.
®
range is guaranteed for 2 years,
Publicidad
