More Information; Troubleshooting; Specifications - Rotel RSP-1068 Manual De Instrucciones

MORE INFORMATION

Troubleshooting

The unit does not turn on.
• Make sure the power cord is plugged into
the rear panel and a live AC wall outlet.
• Make sure the rear panel POWER switch
is in the ON position
No sound from any input.
• Make sure that MUTING is off and VOLUME
is turned up.
• Make sure that preamp outputs are con-
nected to a power amplifier and that the
amplifier is turned on.
• Make sure source inputs are connected and
configured correctly.
No sound from digital sources.
• Make sure that digital input connector is
assigned to the proper source input and
that the source input is configured to use the
digital input rather than an analog input.
• Check the configuration of the DVD player
to ensure that the bitstream and/or DTS
digital output is activated.
No sound from some speakers.
• Check all power amp and speaker connec-
tions.
• Check Speaker Configuration settings in
the Setup menus.
No video output on TV monitor.
• Make sure that the TV monitor is connected
properly. Component video outputs can send
any type of signal to the TV. Composite
video connections can only send video
from composite sources and S-Video con-
nections can only send video from S-Video
sources.
• Make sure the NTSC/PAL switch is set
properly.
OSD menus are not displayed on TV
Monitor.
• Go to Setup menus and configure OSD
menus to be displayed on the TV moni-
tor.
• In some PAL systems, the menus may not
be displayed unless there is an active video
signal.
• When using progressive scan video signals,
make sure that the progressive mode is
selected for that video input in the OTHER
OPTIONS setup menu. This allows the dis-
play of the main setup OSD menus on the
TV monitor by interrupting the progressive
scan video signal and restoring it after the
OSD menus are cancelled. The temporary
information screens (such as volume, etc.)
cannot be displayed on the TV monitor
when progressive scan signals are being
used.
Video and Audio do not match.
• Check that the proper video source is
selected for each input.
• Check that the group delay (lip-synch)
setting is not misadjusted.
Clicking or popping sounds when
switching inputs.
• The unit uses relay switching to preserve
maximum sound quality. The mechanical
clicking of the relays is normal.
• During switching, it may take a split second
for digital signals to be recognized and
properly decoded. Rapid repeated switch-
ing between inputs or settings can result in
clicks or pops from the speakers as the unit
attempts to lock on to the rapidly changing
signals. This causes no harm.
Controls do not operate.
• Make sure that fresh batteries are installed
in the remote.
• Make sure that the IR sensor on the front
panel is not blocked. Aim the remote at the
sensor.
• Make sure the sensor is not receiving strong
IR light (sunlight, halogen lighting, etc.)
• Unplug the unit from the AC outlet, wait
30 seconds, and plug it back in to reset.
40
Specifications
Audio
Total Harmonic Distortion
<0.008%
Intermodulation Distortion (60 Hz:7 kHz)
<0.008%
Frequency Response
10 Hz – 120 kHz, ±3dB (analog bypass)
10 Hz – 95 kHz, ±3dB (digital input)
Signal to Noise Ratio (IHF A-weighted)
95dB (analog bypass)
92dB (Dolby Digital, dts) 0dBFs
Input Sensitivity/Impedance
Line Level: 200 mV/100K ohms
Preamp Output Level/Output Impedance
1.0 V / 1K ohms
Contour (LF/HF)
±6dB at 50 Hz/15 kHz
Decodable Digital Input Signals
Dolby Digital, Dolby Digital EX, DTS, DTS-ES,
DTS 96/24, LPCM (up to 192K), HDCD, MP3,
MPEG Multichannel
Video
Frequency Response
3 Hz – 10 MHz, ± 3dB (Digital Input)
3 Hz – 100 MHz, ± 3dB (Component Video)
Signal to Noise Ratio
45dB
Input Impedance
75 ohms
Output Impedance
75 ohms
Output Level
1.0 volt
General
Power Consumption:
48 watts
8 watts (standby)
Power Requirements (AC)
115 volts, 60Hz (USA version)
230 volts, 50Hz (CE version)
Weight
8.4 Kg/18.5 lb.
Dimensions (W x H x D)
432 x 122 x 341 mm
17.01" x 4.8" x 13.43"
Front Panel Height
(feet removed for rack mount)
109 mm / 4.29"
When sizing openings in custom cabinets, measure the
unit to be installed and/or allow at least 1 mm clearance
on all sides for unit to unit tolerances.
All specifications are accurate at the time of printing.
Rotel reserves the right to make improvements without
notice.
Rotel and the Rotel HiFi logo are registered trademarks
of The Rotel Co, Ltd., Tokyo, Japan.