Remote Control - Revell Control 23897 Manual Del Usuario

Maintenance and care:
• Please only use a clean, damp cloth
to wipe off the model.
• Protect the model and batteries from
direct sunlight and/or direct heat.
• Never allow the remote control and
charging unit to come into contact
with water, because the electronics
will be damaged as a result.
Technical changes and differences in
color reserved!
1A Rotor shaft with main gear wheel
1B Camera lens
1C LEDs
1D Battery compartment

2 REMOTE CONTROL

2A No function
2B No function
2C Control for thrust and rotation
2D Photo button
2E Power LED
2F Antenna
2G Turbo button
2H Button for Headless Mode
2I Control for forwards/backwards and
sideways flight
3 INSERTING BATTERIES (REMOTE CONTROL)
3A Unscrew and remove the cover.
3B Insert 4 x 1,5 V AA batteries and pay attention to the polarity,
as shown in the battery compartment.
3C Close the battery cover and secure with the screw.
16
Required batteries for the model:
Power supply:
Rated output:
1 x DC 3,7 V / 3 Wh
rechargeable
LiPo battery (included)
Capacity: 800 mAh
Battery requirement for the
remote control:
Power supply:
DC 6 V
Batteries:
4 x 1,5 V "AAA"
(not included)
1 MODEL
1E ON/OFF switch
1F SD card slot
1G Camera
2J Trim for forwards/backwards
2K Trim for sideways
2L ON/OFF switch
2M Button for lift-off
2N Button for landing
2O Battery compartment cover
2P Video button
2Q Securing screw
4 CHARGING THE MODEL
Attention: The battery and motor must cool down for 15 to 30 minutes before
charging and after every flight. Otherwise they can be damaged. The charging process
must be constantly monitored. Always ensure that the charging process takes place on
a fireproof surface in a fire-resistant environment.
• Remove the battery from the model 4A. Plug the USB charger into an open USB port
4B. The status LED on the charger begins to illuminate continuously.
• Plug the battery plug into the charging socket of the charger, ensuring correct polarity
4C. The battery must be gently inserted into the charging socket –
DO NOT USE FORCE. If the battery is not correctly inserted into the charging socket,
the battery may become damaged and, under certain circumstances, cause injury.
• The status LED on the USB charger goes out when the charging process starts.
• The charging process lasts approx.70-80 minutes and must be continuously
monitored. The status LED illuminates continuously as soon as the charging process is
finished.
• Disconnect the battery from the charger and disconnect the charger from the USB
port once charging is complete.
The model can fly for approx. 5-7 minutes after a charge time of approx.
70-80 minutes.
Warning notice: The battery does not normally heat up while charging. If it should
become warm or even hot and/or changes to the surface begin to appear, immediately
discontinue the charging process!
5 START PREPARATION
The model must be switched on first in order to connect it to the remote control. To
do this, push the battery into the battery compartment 5A on the model and connect the
battery plug with the battery connection cable. If the battery is not correctly inserted into
the charging socket, the battery may become damaged and, under certain circumstances,
cause injury. Do not use force and ensure the correct polarity.
To switch on the remote control, move the ON/OFF switch 2L to ON 5B.
Then switch the ON/OFF switch on the model 5C to ON. Place the model on the
ground so that its tail points toward you 5D. Press the button 2M to lift off. The model
automatically climbs to an altitude of approximately 1m. Press the button 2N to land.
Attention: If the model does not land correctly, immediately move the control for
thrust and rotation 2C to the bottom left and move the control for forward/backwards
and banking 2I to the bottom right at the same time 5D.
Tip: The rotors can also be started and switched off manually. For this purpose, move
the control for thrust and rotation 2A to the bottom left and move the control for
forward/backwards and banking 2B to the bottom right at the same time 5F.
Once you have finished flying, switch the model off first and then the remote control.
17