DeVilbiss SleepCube AUTOADJUST PAP Serie Manual Del Usuario página 21

Quick View Menu Layout
The Quick View Menu shows a summary of information which is reported in the SmartCode data. Information in the Quick
View includes: Number of days used more than 4 hours (or can be set to 5 hours by clinician), AHI (Apnea/Hypopnea
Index), High Leak percent (percent of time at leak >95 L/m) and Daily Usage (average hours per day used). Each
parameter can be viewed in any of four time periods: 1 day, 7 days, 30 days and 90 days.
The following chart shows the Quick View information that is available on your CPAP display if viewing this information has
been enabled by your provider. The Quick View menu shows a summary of your SmartCode data for 1, 7, 30 and 90 day
periods. Each of the time periods contains info for "Number of Days > x hrs", Apnea Hypopnea Index (AHI), High Leak %
(>95 L/m) and Average Daily Hours of while breathing use.
Diagram of CPAP displays
Days ≥ 4H 1d
1/ 1 (100%)
AHI 1d
31.5+
High Leak 1d
31+%
Daily Usage 1d
9.3+ hours
Exit Menu
Press 
SmartCode Data and Adherence Score Information
Your Healthcare provider may contact you to retrieve SmartCode data and Adherence Score information. To display the
SmartCode data, press the LEFT arrow key once. Use the UP arrow or DOWN arrow keys to change the SmartCode
reporting period. Press the LEFT arrow key again to display the Adherence Score.
NOTE–To ensure accurate SmartCode information, the CPAP should remain plugged in and powered during the day. Do
not unplug daily.
Definitions
Not all of the features in the table below are available in all models. Some are optional, and some depend on what your
physician and/or home care provider has selected. The table below shows the items you may see and describes the
feature associated with each item. Also, some features are only available in certain modes or with the DeVilbiss SmartLink
Therapy Management Module. These are noted in the 'Mode' column below. If you do not see some of these options, your
model or configuration does not support them.
Please note that the values displayed are examples only.
Display Example
OFF
Quick View Menu
Press 
P: 5.0
Heat:Off
Upper Limit
15.0 cmH O
2
Lower Limit
5.0 cmH O
2
SE-DV54-1
Days ≥ 4H
7/ 7 (100%)
AHI
31.5+
High Leak
31+%
Daily Usage
9.3+ hours
Description
Blower OFF. The CPAP unit is plugged in to AC or DC power with the
blower OFF.
Pressing the down key enters the Quick View menu. NOTE: The
"Quick View" menu is only shown if enabled from the clinical menu.
This is the default screen when the device is turned on. The actual
Auto
mask pressure and heater setting are shown. The displayed pressure
may vary slightly while breathing. If the heater system is not connected,
the heat setting will be blank.
This is a prescription setting which limits the maximum pressure at
which the device will operate if in AutoAdjust mode. Your home care
provider programs this setting for you during device setup.
This is a prescription setting which sets the minimum pressure at which
the device will operate in AutoAdjust mode. Your home care provider
programs this setting for you during device setup.
7d Days ≥ 4H
30/30 (100%)
7d AHI
31.5+
7d High Leak
31+%
7d Daily Usage
9.3+ hours
UP () DOWN () buttons
30d Days ≥ 4H
90/90 (100%)
30d AHI
31.5+
30d High Leak
31+%
30d Daily Usage
9.3+ hours
90d
90d
90d
90d
Mode
All
All
All
AutoAdjust
Mode
AutoAdjust
Mode
EN - 21