Technical Features - Jacuzzi experience ALIMIA Ficha Técnica De Preinstalación

It is the responsibility of the installer/owner to ascertain
compliance with specific local regulations prior to installa-
tion.
Jacuzzi Europe S.p.A. gives no guarantee in this respect
and refuses all responsibility regarding compliance of the
installation carried out.

Technical Features

i
Alimia Experience ( 1) includes:
- a control unit, called "Spa-Pak"
it is possible to additionally add a spa-pak "booster kit"
NOTE:
i
(optional,
2-2a, n°33
supplied as standard; refer to the relative documenta-
tion.
i
- the balance tank (
1, V/V1
to hold water that overflows when users get into the tub. Its nomi-
nal capacity is 1,000 litres (operating with about 800-850 litres).
i
- the Hot tub ( 1, C), is to be connected, with hoses, to the "Spa-
Pak", the balance tank and the drain.
MAXIMUM ABSORPTION FOR THE SYSTEM
SINGLE-PHASE TOP
• version with heater
Power supply (x)
Volt Hertz Ampere
220-240 ~ 50/60
25,5 (k)
• version with exchanger
Power supply (x)
Volt Hertz
220-240 ~ 50/60
19,5 (k)
(k): at 230 V - (j): power absorption
(x): see the "electrical preparations" chapter
THREE-PHASE
Alimentazione Consumo tot. riscaldatore
(trifase) elettrico+pompe+fari
Volt Hertz Ampere
(*) 50/60
220 - 240 3~ 45
50/60
26
380 - 415 3N~
(*): special standard (non valido per l'Europa)
WEIGHTS
HOT TUB
Net weight average fill
kg
litres
~ 1350
~180
concentrated load on
resting surface
resting surface
m 2 kg/m 2
~1,12 ~1643
i
.
( 1, A)
) to be connected to the one
) which, once connected, is required
Total consumption
hydro + filtering + heater (3 kW)
kW
5,75 (j)
Total consumption
hydro + filtering
Ampere kW
4,25 (j)
(12 kW) Consumo tot. solo pompe e fari
(vers. scambiatore)
kW Ampere
(j)
17 13
(j)
17
8
(j): potenza assorbita max.
maximum
max. weight
water volume
litres
~ 1660 ~1840
LOWERED
BALANCE TANK (V1)
BALANCE TANK (V)
SPA-PAK
Heat exchanger (optional)
- MAX primary circuit temperature .............................................................50 °C
- Connections.....................................................................................................................3/4"
- Primary circuit flow rate ..............................................................................38 l/min
- Primary pressure drop .....................................................................0,271 m H 2 O
Components
Components and the necessary connections for setting up the system
are described below (see
Hot tub and plumbing
1 overflow channel with grid
2 buttons
2a box for connection of buttons
3 low-point drain with gate valve
to the balance tank (overflow lines)
4A1+4B1
4A2+4B2 to the balance tank (overflow lines)
4C1/4C2 from the overflow channel (overflow lines)
5 hydromassage pump suction lines
6 hydromassage pump delivery lines
7 filtering suction line
8 suction line from the balance tank
9 filtering return line
10 blower line (optional)
11 connections to the water system
12 perimeter metal supports
Spa-pak
13, 13a Electric wiring box
14 optional - 14b: heater or 14a: heat exchanger
15 hydromassage pumps
16 filtering pump
17 blower
18 quartz sand filter
kW
19 safety switch
(j)
5
20 temperature sensor
(j)
5
21 flow switch (models with heater)
balance tank
22 water loading/filling solenoid valve (3/4")
23 level switches
24 check valve
Total
25 gate valve (for emptying)
kg
26 pre-filters
27 overflow
28, 29 ground drainage points
30 gate valves (for system maintenance)
31 gate valves (for suction balancing)
16
max weight
ground resting surface
at full load
kg m 2
~ 900 ~ 1,8
~ 925 ~ 1,2
~ 285 ~ 1,1
i
2-2a).
ground load
kg/m 2
~ 500
~ 770
~ 260