Detergent (Axp) System Preparation & Use - Nilfisk-Advance AquaRide Instrucciones De Uso

A-10 / ENGLISH
DETERGENT (AXP) SYSTEM PREPARATION AND USE
COMMON INSTRUCTIONS:
The system should be purged of previous detergent when switching to a different
detergent. SERVICE NOTE: Move machine over fl oor drain before purging
because a small amount of detergent will be dispensed in the process.
To Purge When Changing Chemicals:
1 Disconnect and remove the detergent cartridge.
2 Turn the Key Switch (J) ON. Press and hold the Purge Switch (T) down
for at least 3 seconds, then press and hold the Solution Switch (R) (on the
main machine's control panel) for the duration of the purge cycle. Holding
the solution switch is necessary to open the solution valve and prevent the
purged detergent from fl owing back into the solution tank. NOTE: Once
activated the Purge Indicator (U) will begin to scroll a fl ashing light from left
to right and will automatically shut off after 10 seconds. Normally one purge
cycle is adequate to purge the system.
To Purge Weekly:
1 Disconnect and remove the detergent cartridge. Install and connect a
Cartridge fi lled with clean water.
2 Turn the Key Switch (J) ON. Press and hold the Purge Switch (T) down
for at least 3 seconds, then press and hold the Solution Switch (R) (on the
main machine's control panel) for the duration of the purge cycle. Holding
the solution switch is necessary to open the solution valve and prevent the
purged detergent from fl owing back into the solution tank. NOTE: Once
activated the Purge Indicator (U) will begin to scroll a fl ashing light from left
to right and will automatically shut off after 10 seconds. Normally one purge
cycle is adequate to purge the system.
The Detergent Box (AA) has a Detergent Level Viewing Slot (BB) for keeping
track of how much detergent is remaining in the cartridge. When the detergent
level is nearing the bottom of this slot it is time to refi ll or replace the cartridge.
General Use:
The detergent injection system is activated when the Key Switch (J) is turned on
but no detergent is dispensed until the scrub system is activated and the Drive
Pedal (8) pushed forward. The solution fl ow rate is determined by the use of
"Maintenance" or "Restoration" mode. The solution fl ow rate can be changed
by pressing the Maintenance Extract Mode Switch (D) for reduced fl ow or the
Restoration Extract Mode Switch (F) for increased fl ow. The detergent fl ow rate
increases or decreases with the solution fl ow rate but the detergent ratio remains
the same. During scrubbing, the detergent system can be turned off at any time
by pressing the Detergent ON/OFF Switch (S) to allow scrubbing with water only.
SERVICE NOTE: Follow the "To Purge Weekly" instructions above if the machine
is going to be stored for an extended period of time or if you plan to discontinue
use of the detergent injection system.
DISPOSABLE CARTRIDGE SPECIFIC INSTRUCTIONS:
Remove the Cap (CC) and place the cartridge in the detergent box. Install the Dry
Break Cap (DD) as shown.
A-10 - FORM NO. 56041627 - AquaRide
NON-DISPOSABLE CARTRIDGE SPECIFIC INSTRUCTIONS:
Fill the detergent cartridge with a maximum of 1.25 gallons (4.73 Liters) of detergent.
SERVICE NOTE: Remove the detergent cartridge from the detergent box prior to fi lling to
avoid spilling detergent on the machine.
It is recommended that a separate cartridge be used for each detergent you plan to use.
The detergent cartridges have a white decal on them so you can write the detergent name
on each cartridge to avoid mixing them up. The detergent cartridge has a Magnetic Slider
(EE) on one end that needs to be set to the proper dilution ratio according to the dilution
instructions on the manufacturer's bottle. Slide the Magnet Slider (EE) to the appropriate
location on Detergent Dilution Ratio Decal (FF). When installing a new cartridge, remove
the Cap (CC) and place the cartridge in the detergent box. Install the Dry Break Cap (DD)
as shown.
, AquaRide AXP
™ ™
revised 3/06