Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
•
Avoid accidental start-up. Make sure that the tool is
in the OFF position before plugging in.
•
Do not force tool. It will work most efficiently at the
rate for which it was designed.
Keep hands away from moving parts and cutting
surfaces.
•
Never leave tool running unattended. Turn the power
off and do not leave tool until it comes to a complete
stop.
•
Do not overreach. Keep proper footing and balance.
Never stand on tool. Serious injury could occur if tool
is tipped or if blade is unintentionally
contacted.
Know your tool. Learn the tool's operation, applica-
tion and specific limitations.
Use of improper accessories
increases the risk of
injury to persons.
Handle workpiece correctly. Protect hands from pos-
sible injury.
Turn machine off if it jams. Blade jams when it digs
too deeply into workpiece. (Motor force keeps it
stuck in the work.) Do not remove jammed or cut off
pieces until the saw is turned off, unplugged and the
blade has stopped.
WARNING: The operation of any power tool can result in
foreign objects being thrown into the eyes, which can
result in severe eye damage. Always wear safety goggles
complying with United States ANSI Z87.1 (shown on
package) before commencing power tool operation.
Safety goggles are available through your Sears catalog.
Check for shipping damage. If damage has occurred, a
claim must be filed with carrier. Check for complete-
ness. Immediately report missing parts to dealer.
The band saw comes assembled as one unit. Additional
parts which need to be fastened to the saw should be
located and accounted for before assembling:
A
Miter Gauge Assembly
B
Table Assembly
C
Locking Handle with Washer
D
Table Locking Insert Assembly
A
B
Figure 1 =Unpacking
C
iMPORTANT: Table is coated with a protectant. To
ensure proper fit and operation, remove coating.
Coating is easily removed with mild solvents, such as
mineral spirits, and a soft cloth. Avoid getting solution
on paint or any of the rubber or plastic parts. Solvents
may deteriorate these finishes. Use soap and water on
paint, plastic or rubber components. After cleaning,
cover all exposed metal surfaces with a light coating of
oil. Paste wax is recommended for table top.
WARNING:
Never use highly volatile solvents. Non
flammable solvents are recommended to avoid possible
fire hazard.
CAUTION:
Do not attempt assembly if parts are miss-
ing. Use operator's manual to order replacement parts.
MOUNT
BAND SAW TO WORK
SURFACE
•
Band saw' is designed to be portable so it can be
moved to job site, but should be mounted to stable,
level bench or table.
Base of band saw has four mounting holes.
If predrilled holes do not exist on work surface, drill
four holes.
Securely mount band saw to work surface by bolting
(hardware not supplied) it through the holes.
NOTE: The blade must be tensioned and tracked, and
the blade guides must be adjusted before operation of
the saw. Refer to "Tracking Blade" and "Blade Guides" in
the OPERATION section, page 6.
iNSTALL
TABLE
Refer to Figure 10.
Remove knob assembly (Key No. 18) from saw
frame.
•
Position table assembly on saw frame. Re-install
knob assembly.
Secure table in position with locking handle assem-
bly (Key Nos. 14 and 15).
•
Using a combination square, set table perpendicular
to blade. Adjust table stop (Key Nos. 12 and 13) if
necessary.
•
Set pointer at 0° (Key No. 21).
•
Install table locking insert assembly (Key Nos. 4, 5, 6
and 16).
Refer to Figures 2 and 3.
MOTOR
The 120 Volt AC motor has the following specifications:
Horsepower (Continuous Duty) ..................
Voltage ...................................
120
Amps .....................................
2.5
Hertz .....................................
60
Phase ..................................
Single
RPM ....................................
1725
POWER SOURCE
The motor is designed for operation on the voltage and
frequency specified. Normal loads will be handled safe-
ly on voltages not more than 10% above or below the
specified voltage.
3
Publicidad
Tabla de contenido
