Ec Declaration Of Conformity - Beninca MS5 Manual De Instrucciones

Manufacturer:
Automatismi Benincà SpA.
Address:
Via Capitello, 45 - 36066 Sandrigo (VI) – Italy
It is hereby stated that the product
automatic system 24Vdc for sliding gates
MS5.
is compliant with provisions set forth in the following EC Directives:
- DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 15 December 2004, on the harmo-
nisation of the laws of Member States relating to electromagnetic compatibility and which cancels Directive 89/336/EEC, according to the
following harmonised regulations: EN 61000-6-2:2005, EN 61000-6-3:2007.
- DIRECTIVE 2006/95/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 12 December 2006, on the harmoni-
sation of the laws of Member States relating to electrical equipment designed for use with certain voltage limits, according to the following
harmonised regulations: EN 60335-1:2002 + A1:2004 + A11:2004 + A12:2006 + A2:2006 + A13:2008; EN 60335-2-103:2003.
- DIRECTIVE 2006/42/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 17 May 2006, on machinery, which
amends Directive 95/16/EC, and complies with the requisites for the "partly completed machinery (almost machinery)" set forth in the
EN13241-1:2003 regulation.
• Moreover, Automatismi Benincà SpA declares that the pertaining technical documentation has been drawn up in compliance with At-
tachment VII B of the 2006/42/ EC Directive and that the following requirements have been complied with: 1.1.1 - 1.1.2 - 1.1.3 - 1.1.5 - 1.2.1
- 1.2.3 - 1.2.6 - 1.3.1 - 1.3.2 - 1.3.3 - 1.3.4 - 1.3.7 - 1.3.9 - 1.5.1 - 1.5.2 - 1.5.4 - 1.5.5 - 1.5.6 - 1.5.7 - 1.5.8 - 1.5.10 - 1.5.11 - 1.5.13 - 1.6.1
- 1.6.2 - 1.6.4 - 1.7.2 - 1.7.4 - 1.7.4.1 - 1.7.4.2 - 1.7.4.3.
• The manufacturer undertakes that information on the "partly completed machinery" will be sent to domestic authorities. Transmission
ways are also included in the undertaking, and the Manufacturer's intellectual property rights of the "almost machinery" are respected.
• It is highlighted that commissioning of the "partly completed machinery" shall not be provided until the final machinery, in which it should
be incorporated, is declared compliant, if applicable, with provisions set forth in the Directive 2006/42/EC on Machinery.
• Moreover, the product, as applicable, is compliant with the following regulations:
EN 12445:2002, EN 12453:2002, EN 12978:2003.
Benincà Luigi, Legal Officer.
Sandrigo, 22/04/2015.
The product shall not be used for purposes or in ways other than
those for which the product is intended for and as described in
this manual. Incorrect uses can damage the product and cause
injuries and damages.
The company shall not be deemed responsible for the non-com-
pliance with a good manufacture technique of gates as well as
for any deformation, which might occur during use.
Keep this manual for further use.
Qualified personnel, in compliance with regulations in force,
shall install the system.
Packaging must be kept out of reach of children, as it can be
hazardous. For disposal, packaging must be divided the various
types of waste (e.g. carton board, polystyrene) in compliance
with regulations in force.
The installer must supply all information on the automatic,
manual and emergency operation of the automatic system and
supply the end user with instructions for use.
•
An omnipolar switch/section switch with remote
contact opening equal to, or higher than 3mm
must be provided on the power supply mains..
10

EC Declaration of Conformity

Directive 2004/108/EC(EMC); 2006/95/EC (LVD)
WARNING
Make sure that before wiring an adequate differential switch
and an overcurrent protection is provided.
Pursuant to safety regulations in force, some types of installa-
tion require that the gate connection be earthed.
During installation, maintenance and repair, cut off power
supply before accessing to live parts.
This product is not to be used by persons (including children)
with reduced physical, sensory or mental capacity, or who are
unfamiliar with such equipment, unless under the supervision
of or following training by persons responsible for their safety.
Descriptions and figures in this manual are not binding. While
leaving the essential characteristics of the product unchanged,
the manufacturer reserves the right to modify the same under
the technical, design or commercial point of view without nec-
essarily update this manual.