Safety And Control Devices; Disposal Of Packaging And The Appliance; Instructions For Installation; Reference Standards And Laws - ALI NP70 Serie Traducción De Las Instrucciones Originales

• At least twice a year, have an authorized technician clean the
internal parts of the appliance.
• Do not use direct or high pressure water jets to clean the
appliance.
• Do not use corrosive products to clean the floor beneath the
appliance.
• Not wash in the dishwasher the body and the flame sprea-
ders of the burners of the cooking hob.
• Do not use flammable products to clean the appliance.

3 SAFETY AND CONTROL DEVICES

SAFETY THERMOSTAT
The manufacturer will not be liable for any damage or in-
jury resulting from failure to observe the following rules.
• The appliance is equipped with a manual reset safety ther-
mostat which interrupts heating when the operating tempera-
ture exceeds the maximum permitted value.
• To restore appliance operation, open the door and press the
thermostat reset button. This procedure may only be carried
out by a qualified, authorized technician.

4 DISPOSAL OF PACKAGING AND THE APPLIANCE

4.1 PACKAGING
The packaging is made using environmentally friendly mate-
rials. The plastic recyclable components are:
• the transparent cover, the bags containing the instructions
manual and nozzles ( made of Polyethylene - PE.).
• the straps (in Polypropylene - PP).
4.2 APPLIANCE
The appliance is manufactured 90% from recyclable metals
(stainless steel, aluminum sheet, copper.... ).
The appliance must be scrapped in compliance with current
regulations governing such disposal.
• It must be disposed of properly.
• Make the appliance unusable before scrapping.
RISKS DUE TO NOISE
• On airborne noise emissions, the A-weighted sound pressure
level is below 70 dB(A).

INSTRUCTIONS FOR INSTALLATION

REMINDERS FOR THE INSTALLER
The manufacturer will not be liable for any damage or in-
jury resulting from failure to observe the following rules.
• Read this manual carefully. It provides important information
for safe installation, use and maintenance of the appliance.
• Installation, conversion to a different type of gas and applian-
ce maintenance must be carried out by qualified technicians
authorized by the manufacturer, in compliance with current
safety standards and the instructions in this manual.
• Identify the specific appliance model. The model number is
detailed on the packaging and on the appliance data plate.
• The appliance must be installed in a well-ventilated room.
• Do not obstruct any air vents or drains present on the ap-
pliance.
• Do not tamper with appliance components.

5 REFERENCE STANDARDS AND LAWS

Install the appliance in conformity to current statutory safety
standards.
Install the appliance in compliance with current regulations.

6 UNPACKING

Check the state of the packaging and in the event of damage,
ask the delivery person to inspect the goods.
• Remove the packaging.
• Remove the protective film from the outer panelsand interior.
Use a suitable solvent to remove any residual adhesive from
the panels.

7 POSITIONING

• The overall dimensions of the appliance and the position of
connections are given on the installation diagram at the start
of this manual.
• The appliance can be installed singly or in combination with
other appliances in the same product range.
• The appliance is not suitable for integrated installation.
• Position the appliance at least 10 cm from adjacent walls.
This distance can be reduced in the presence of non-combu-
stible walls or heat-insulated walls.
• Level the appliance by means of the height-adjustable feet.
• The benchtop appliance weighing less than 40 kg, if installed
singularly, it must be fixed using the appropriate flanged feet.
7.1 APPLIANCE ASSEMBLY WITH BASE, BRIDGE, AND
CANTILEVER SOLUTIONS
Follow the instructions provided with the type of support utili-
zed.
7.2 FIXING THE APPLIANCE TO THE FLOOR
Appliances of 40cms in width installed alone must be fixed to
the floor. Use the flanged feet provided.
7.3 JOINING APPLIANCES TOGETHER IN LINE
• Remove the control panels (A).
• Remove the fixing screw nearest the panel from each of the
sides to be joined( B ).
• Place the appliances side by side and adjust the tops to the
same height (C).
• Insert the connector plate ( supplied ) in the seat provided on
the side of the top. Join the appliances by screwing down the
connector plate (D) using the flat-headed M5 screws (sup-
plied).
• Turn one of the two internal tabs of the appliances to be joi-
ned by 180° (E).
• Join the appliances by screwing the M5x40 screw on the op-
posite insert (F).

8 FUMES EXHAUST SYSTEM

Create a fumes exhaust system based on the "Type" of ap-
pliance.The "Type" is stated on the appliance data plate.
8.1 APPLIANCE TYPE "A1"
• Position the "A1" type appliance below an extractor hood to
ensure smoke and fumes generated by cooking are removed.
8.2 APPLIANCE TYPE "B21"
• Position the "B21" type appliance below an extractor hood.
8.3 APPLIANCE TYPE "B11"
• Fit the "B11" type appliance with a suitable flue, available
from the appliance manufacturer. Follow the assembly in-
structions provided with the flue.
3