Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
fa
Keep cutting tools sharp and clean.
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
ga
Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
5) SERVICE
aa
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
ba
In case of consuming of the carbon brushes to
send the tool by assistance authorized technique
for substitution. Carbon brushes are of specify them
cause damages to the motor of the tool.
ca
If the power cord is damaged, the power cord shall
be replaced by manufacturer, service or qualified
person to avoid the risk of electrical shock.
SAFETY INSTRUCTIONS FOR
ROUTERS GENERAL
GENERAL
•
This tool should not be used by people under the age of
16 years.
Always disconnect plug from power source before
•
making any adjustment or changing any accessory.
ACCESSORIES
•
SKIL can assure flawless functioning of the tool only when
•
original accessories are used.
•
Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool.
•
Do not use damaged or deformed router bits.
•
Only use sharp router bits.
•
Protect accessories from impact, shock and grease.
•
Only use high speed steel (HSS) or carbide-tipped (CT)
•
router bits with this tool
BEFORE USE
•
Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working.
•
Always check that the supply voltage is the same as
the voltage indicated on the nameplate of the tool (tools
with a rating of 230V or 240V can also be connected to
a 220V supply).
•
Do not work with materials containing asbestos.
•
Clamp the workpiece in case it does not remain
stationary from its own weight.
•
Do not clamp the tool in a vice.
•
Use completely unrolled and safe extension cords with
a capacity of 16 Amps (UK 13 Amps).
•
The noise level when working can exceed 85 dB(A);
wear ear protection.
•
Wear a dust protection mask when working with
materials which produce dust that is detrimental to
health; inform yourself beforehand about the materials
to be worked on.
•
Be sure tool is switched off when plugging in.
Properly
.
DURING USE
•
Always keep the cord away from moving parts of the
tool; direct the cord to the rear, away from the tool.
•
Never use tool when cord or base-plate
(=protective guard) is damaged; have it replaced by a
qualified person.
•
Keep hands and fingers away from router bit when tool
is switched on.
•
Never exceed maximum cutting depth of router bit
(Measure "B" in the figure 21) while cutting.
•
In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug.
•
In case the router bit is blocked, resulting in jerking
forces on the tool, immediately switch off the tool.
•
In case of current interruption or when the plug is
accidentally pulled out, immediately switch off the tool
in order to prevent uncontrolled restarting.
•
Do not apply so much pressure on the tool that it comes
to a standstill.
AFTER USE
•
After finishing the work, turn off your power tool
positioning the switch F (fig. 2) in position 0 and remove
the plug.
Symbols
The following symbols show the correct use for your power
tool. Please write down the symbols and their meanings.
The correct interpretation of the symbols will help you use
the machine in a better and safer way.
Symbol
•
•
•
USE
–
Adjust the cutting depth
Screw out the fixing knob D and E (fig. 1) untill loose.
Adjust the acrylic base to your satisfied depth and
screw the fixing knob to be tightly.
–
Swicth ON and OFF
To turn the turn working, just turn the swicth button F
to "I" position. To turn off the tool, just turn the swicht
button to "O" position.
!
The tool must to be turned before the base touch
the piece of work
!
before hanging up the tool, it should raise
theworkpiece
18
A (figure 1)
Meaning
Electrical insulation class II.
Read the instructions before
working with the power tool.
When using the tool wear goggles
and ear plugs..
ı
ˆ
Publicidad
Tabla de contenido
