Technical Data - Rover BE-M 10 Instrucciones Para El Uso

Bombas y electrobombas - autocebantes doble sentido
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 14
GB - INTRODUCTION
ELECTRIC PUMP: Device consisting in three parts - mechanical, hydraulic and electric. The aim of these provisions for the use and maintenance of said electric pump is to set down regulations for the safety of people, and
prevent damage being caused to the area around the pump.
This safety does not depend on observing these provisions alone, but on the correct installation, maintenance and use of the pump in conformity with its destination of use as well.
Read both these documents and any enclosures carefully before installing the pump. Installation and operation must conform to the safety standards in force in the country where the pump is installed. Operation must be carried
out professionally.
WARNING: Users who do not respect these safety standards will not only create a dangerous situation for people and damage the pump itself, but forfeit the right to claim for work to be carried out under warranty, too.
Carefully read, and make sure you thoroughly understand, this Instruction Booklet before using the pump. Anyone unable to do so, for any reason whatsoever must not be allowed to operate the pump.
RUSTPROOF ELECTRIC PUMPS FROM THE "NOVAX" RANG
The rustproof electric pumps from the "NOVAX" range are particularly suitable for pouring liquid foodstuffs. The hydraulic part of the pump is manufactured in a special solid rustproof alloy. This new technology enables ROVER
POMPE to issue the important Certificate of Suitability for pouring wine and liquid foodstuffs with similar characteristics.
PRELIMINARY REMARKS
All the ROVER POMPE electric pumps manufactured for pouring liquids carry a warranty both for their operation and the materials used to manufacture them. When used correctly, therefore, following the instructions below, and
subjected to ordinary maintenance, the pumps will perform as they were built to.
The pumps are extremely reliable, self-aspiring and/or self-priming, easy to clean and will satisfy difficult pouring demands. They can be used in any situation in which the conditions of corrosion do not call for the use of an acid-
resistant pump. Being able to resist any kind of liquid for short periods of time, they can also be utilised in an emergency.
The special feature which makes ROVER POMPE pumps stand out from the others currently available on the market is the fact that they have an electric switch. This switch means
the motor can rotate in two directions, namely clockwise and/or anticlockwise indifferently.
All products are covered by a general, two-year warranty, which starts the date the material is shipped.
PRELIMINARY INSPECTIONS
The electric pump is supplied, ready for installation, in sturdy cardboard boxes complete with an Instruction Booklet. Remove the pump from the wrapping and check it carefully. Contact the supplier if you should notice that any
damage has been caused to the pump during transportation, and be ready to explain the nature of this damage.
WARNING: if you are doubtful of the safety of the machine do not use it.
LUBRICATION
All moving parts are lubricated in our factory during construction. Do not oil or grease moving parts as this could cause them irreparable damage.

TECHNICAL DATA

This is a classical self-aspiring, DUAL ROTATION pump, complete with lateral liquid ring, and star impeller. This particular kind of hydraulic solution means the pump has an extraordinary self-priming capacity, even when air
bubbles or gases obstruct the smooth flow of the liquid in the suction tube.
The pump is particularly suitable for pouring and/or transferring liquids which have previously been decanted, such as:
WINE - MUST - VINEGAR - MILK – FRESH WATER - SALTWATER – ORGANIC SOLVENTS – EMULSION FERTILISERS - OIL, with a viscosity of no greater than 4 (four) ENGLER degrees or 30 (thirty) CENTISTOKES
The liquids to be poured must be both clean and neutral. However, they can contain a small percentage of solids (0.2–0.5% max) in suspension. The hardness and granulometry of the said suspension must be such that they do
not wear out the internal surfaces of the pump. A filter with a very fine mesh mounted on the aspiration tube can be used in extreme cases.
WARNING: do not use the pump for pouring concentrated acids, petrol or solvents.
DECLARATION OF CONFORMITY:
Manufacturing company: ROVER POMPE Snc, Via dell'Artigianato, 4 Z.A., 35020 Polverara (Padua) Italy
ROVER POMPE Snc hereby declares that all the electric pumps manufactured in its factory in Polverara (Padua) Italy conform to the following safety standards for electrical appliances:
60335-1 / 60335-2 , B.T. 2006/95/CEE, 73/23 CEE, 98/37/CEE in 93/68/CEE, 2000/14/CE
 ROVER POMPE snc – 2009/2010 page - 26 -

Publicidad

Tabla de contenido
loading

Tabla de contenido