Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
EM UNV34 Configurations
MLL
LED PCB 1
EM UNV1
BATTERY
BATTERY
CONNECTORS
CHARGER/
CONNECTORS
DRIVER
BOARD
"OPTIONAL
CONTROL"
"OPTIONAL
JUMPER
CONTROL"
OPTIONAL CONTROL
JUMPER
RED
BLACK
BLACK
EM to 2 Foot Linear Fixture
IF 1740 • 11/15
Figure 3
SUPPLY WIRE
G
N
L
LYNX POWER RECEPTACLE, OPTIONAL,
OR WAGO LEVERLOCK CONNECTORS
FOR CUSTOMER WIRING
WHITE
BLACK
GREEN
(DC+)
(DC-)
G
N
L
(GREEN)
N
L
(BROWN)
(BLUE)
DRIVER
INPUT
PURPLE (+)
GRAY (-)
OUTPUT
+ (RED)
- (BLACK)
2X
APPROVED
TERMINATION
LINE
NEUTRAL
2X
POSITIVE
3 POLE SPLICE
NEGATIVE
CONNECTOR
GROUND
CN2 -
CN1+
LED PCB 2
CN2 -
CN1+
RED
RED
BLUE
BLACK
BLACK
BATTERY 2
BLUE
RED
RED
BATTERY 1
BLACK
BLACK
TB1
GREEN
GRAY
BLUE
BLUE
ORANGE
BLACK
GRN
WHT
OPTIONAL SURGE
SUPPRESSOR
BLK
GREEN
BLUE
POWER SUPPLY
BROWN
RED
Figure 4
Copyright © 2015, Eaton's Crouse-Hinds Division
3X 2 OR 3
POLE SPLICE
CONNECTOR
DIMMING LEADS
0-10 VDC SIGNAL
10V = 100% LIGHT OUTPUT
BATTERY
CONNECTORS
DIMMING
BATTERY BACK-UP UNIT TO LIGHTING FIXTURE
CONTROL
SIGNAL WIRE
1.
Ensure the branch circuit supply to the luminaire, as indicated in Figures 4 and
G
5, is powered off before proceeding.
SUPPLY
N
WIRE
2.
Locate the driver housing cover on the luminaire housing and open by
L
loosening the four (4) #10-32 X 0.75" stainless steel cover screws (see Figure
6). Detach the (-) (BLACK) and the positive (+) (RED) driver output wires from
the splice connector per the wiring diagrams (see Figure 4 or 5) and terminate
ends using methods that comply with all applicable codes. The driver is not to
be removed from the fixture. Bring in the output wires that were previously
connected to the battery back-up enclosure to the LED board wires. Attach
the positive (+) LED output to LED board from the battery back-up unit to the
positive (+) splice connector in the linear LED fixture. Attach the negative (-)
LED output to LED board from the battery back-up unit to the negative (-) splice
connector in the linear LED fixture.
3.
Re-install the driver housing cover and tighten all four (4) cover mounting
screws 32 in.-lbs. (3.6 N-m).
4.
Replace any damaged or missing cover screws. Consult factory for
replacement parts.
5.
The battery connectors per Figure 4 or 5
are shipped disconnected. Locate these
connectors and make the connections
for battery 1 and battery 2 per Figure 4
or 5. Ensure the red and black wires are
aligned correctly on each connector.
SUPPLY WIRE
G
N
LYNX POWER RECEPTACLE, OPTIONAL,
OR WAGO LEVERLOCK CONNECTORS
FOR CUSTOMER WIRING
WHITE
GREEN
(DC+)
G
G
(GREEN)
DRIVER
OUTPUT
- (BLACK)
LINE
NEUTRAL
POSITIVE
NEGATIVE
GROUND
CN2 -
LED PCB 1
CN1+
CN2 -
LED PCB 3
CN1+
EM UNV1
RED
RED
BLACK
BLACK
BATTERY 2
RED
RED
BLACK
BATTERY 1
BLACK
BATTERY
CONNECTORS
CHARGER/
DRIVER
BOARD
GREEN
GRAY
"OPTIONAL
BLUE
CONTROL"
"OPTIONAL
BLUE
JUMPER
CONTROL"
ORANGE
OPTIONAL CONTROL
JUMPER
BLACK
RED
BLACK
OPTIONAL SURGE
SUPPRESSOR
BLACK
POWER SUPPLY
RED
Figure 5
EM to 4 Foot Linear Fixture
Figure 6
L
BLACK
(DC-)
L
N
3X 2 OR 3
POLE SPLICE
L
N
CONNECTOR
(BLUE)
(BROWN)
INPUT
PURPLE (+)
GRAY (-)
DIMMING LEADS
0-10 VDC SIGNAL
10V = 100% LIGHT OUTPUT
+ (RED)
2X APPROVED
TERMINATION
2X
5 POLE SPLICE
CONNECTOR
CN1+
LED PCB 2
CN2 -
CN1+
LED PCB 4
CN2 -
BLUE
BLUE
TB1
DIMMING
CONTROL
SIGNAL WIRE
G
SUPPLY
N
WIRE
L
GRN
WHT
BLK
GREEN
BLUE
BROWN
Page 2
Publicidad
Tabla de contenido
