Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
2.2
INSPECTION FREQUENCY: SRDs shall be inspected by the user (authorized person
(See Table 3). Additionally, inspections shall be conducted periodically by a competent person
CSA also requires periodic Product Revalidation by an Authorized Service Center. Extreme working conditions (harsh
environment, prolonged use, etc.) may necessitate more frequent Competent Person Inspection and Product Revalidation.
The competent person will use the Inspection Schedule (Table 2) to determine appropriate inspection and revalidation
intervals. Inspection procedures are described in the Inspection & Maintenance Log (Table 3). Results of the Competent
Person inspection should be recorded in the Inspection and Maintenance Log or recorded with the Radio Frequency
Identification (RFID) system (see Section 5).
2.3
NORMAL OPERATIONS: Normal operation will allow the lifeline to extend and retract with no hesitation or slack as
the worker moves at normal speeds. If a fall occurs, a speed sensing brake system will activate, stopping the fall and
absorbing much of the energy created. Sudden or quick movements should be avoided during normal work operation, as
this may cause the SRD to lock up. For falls which occur near the end of the lifeline travel, a reserve lifeline system or
Energy Absorber has been incorporated to reduce the fall arrest forces.
2.4
BODY SUPPORT: A Full Body Harness must be used with the Self-Retracting Device. The harness connection point must be
above the user's center of gravity. A body belt is not authorized for use with the Self-Retracting Device. If a fall occurs when
using a body belt it may cause unintentional release or physical trauma from improper body support.
2.5
COMPATIBILITY OF COMPONENTS: Unless otherwise noted, 3M equipment is designed for use with 3M approved
components and subsystems only. Substitutions or replacements made with non approved components or subsystems may
jeopardize compatibility of equipment and may affect safety and reliability of the complete system.
2.6
COMPATIBILITY OF CONNECTORS: Connectors are considered to be compatible with connecting elements when they
have been designed to work together in such a way that their sizes and shapes do not cause their gate mechanisms to
inadvertently open regardless of how they become oriented. Contact 3M if you have any questions about compatibility.
Connectors (hooks, carabiners, and D-rings) must be capable of supporting at least 5,000 lbs. (22.2 kN). Connectors
must be compatible with the anchorage or other system components. Do not use equipment that is not compatible.
Non-compatible connectors may unintentionally disengage (see Figure 5). Connectors must be compatible in size, shape,
and strength. Self-locking snap hooks and carabiners are required. If the connecting element to which a snap hook or
carabiner attaches is undersized or irregular in shape, a situation could occur where the connecting element applies a
force to the gate of the snap hook or carabiner (A). This force may cause the gate to open (B), allowing the snap hook or
carabiner to disengage from the connecting point (C).
2.7
MAKING CONNECTIONS: Snap hooks and carabiners used with this equipment must be self-locking. Ensure all
connections are compatible in size, shape and strength. Do not use equipment that is not compatible. Ensure all
connectors are fully closed and locked. 3M connectors (snap hooks and carabiners) are designed to be used only as
specified in each product's user's instructions. See Figure 6 for examples of inappropriate connections. Do not connect
snap hooks and carabiners:
A.
To a D-ring to which another connector is attached.
B.
In a manner that would result in a load on the gate. Large throat snap hooks should not be connected to standard
size D-rings or similar objects which will result in a load on the gate if the hook or D-ring twists or rotates, unless the
snap hook is equipped with a 3,600 lb (16 kN) gate.
C.
In a false engagement, where size or shape of the mating connectors are not compatible and, without visual
confirmation, the connectors seem fully engaged.
D.
To each other.
E.
Directly to webbing or rope lanyard or tie-back (unless the manufacturer's instructions for both the lanyard and
connector specifically allows such a connection).
F.
To any object which is shaped or dimensioned such that the snap hook or carabiner will not close and lock, or that
roll-out could occur.
G.
In a manner that does not allow the connector to align properly while under load.
Type of Use
Application Examples
Infrequent to Light
Rescue and Confined
Space, Factory
Maintenance
Moderate to Heavy
Transportation,
Residential Construction,
Utilities, Warehouse
Sever to Continuous
Commercial Construction,
Oil and Gas, Mining,
Foundry
CSA Inspection Criteria:
• Failure of the Worker to inspect before each use, or failure of the Before Use Inspection, will require inspection by a Competent Person.
• Failure of the Competent Person to inspect at the proper intervals, or failure of the Competent Person Inspection, will require Product Revalidation or disposal.
• The Type of Use category will be determined by a Competent Person.
• SRDs considered non-repairable, or SRDs designed such that internal inspection will render the SRD unserviceable, are not subject to Product Revalidation. These
SRDs
will have service life and other inspection requirements as provided in the manufacturer's instructions.
1 Authorized Person: A person assigned by the employer to perform duties at a location where the person will be exposed to a fall hazard.
2 Rescuer: Person or persons other than the rescue subject acting to perform an assisted rescue by operation of a rescue system.
3 Competent Person: An individual designated by the employer to be responsible for the immediate supervision, implementation, and monitoring of the employer's
managed fall protection program who, through training and knowledge, is capable of identifying, evaluating, and addressing existing and potential fall hazards, and
who has the employer's authority to take prompt corrective action with regard to such hazards.
Table 2 – Inspection Schedule
Conditions of Use
Good Storage Conditions, Indoor
or Infrequent Outdoor Use, Room
Temperature, Clean Environments
Fair Storage Conditions, Indoor and
Extended Outdoor Use, All Temperatures,
Clean or Dusty Environments
Harsh Storage Conditions, Prolonged
or Continuous Outdoor Use, All
Temperatures, Dirty Environment
14
or rescuer
) before each use
1
2
other than the user.
3
ANSI/CSA
Competent
User
Person
Before Each
Annually
At least every 5 years but
Use
not longer than the interval
required by the manufacturer.
Before Each
Semi-Annually
At least every 2 years but
Use
to Annually
not longer than the interval
required by the manufacturer.
Before Each
Quarterly to
At least annually but not
Use
Semi-Annually
longer than the interval
required by the manufacturer.
CSA
Product Revalidation
Publicidad
Tabla de contenido
