Stanley SCI12 Manual De Instrucciones página 25

The variable speed switch enables you to select the best
speed for a particular application. The further you squeeze
the trigger, the faster the tool will operate. For maximum tool
life, use variable speed only for starting holes or fasteners.
Note: Continuous use in variable speed range is not
recommended. It may damage the switch and should be
avoided.
Forward/Reverse control button (Fig. A)
A forward/reverse control button (2) determines the
direction of the tool and also serves as a lock-off button.
To select forward rotation, release the trigger switch and
depress the forward/reverse control button on the right
side of the tool. To select reverse, depress the forward/
reverse control button on the left side of the tool. The
center position of the control button locks the tool in the off
position. When changing the position of the control button,
be sure the trigger is released.
Note: The first time the tool is run after changing the
direction of rotation, you may hear a click on start up.
This is normal and does not indicate a problem.
Worklight (Fig. A)
There is a worklight (7) located under the chuck collar.
The worklight will be activated when the trigger switch is
squeezed.
Note: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Quick-Release chuck (Fig. A and D)
Note: The chuck accepts 1/4" (6.35 mm) hex accessories
allows better access in tight spaces.
f Place the forward/reverse button (2) in the locked off
(center) position or remove battery pack before
changing accessories.
f To install an accessory, push accessory to fully insert
into chuck (4). The chuck collar (3) does not need
to be pulled up to lock accessory in place.
f To remove an accessory, pull the chuck collar (3)
away from the front of the tool. Remove the accessory
and release the collar.
USAGE
Caution! Ensure fastener and/or system will withstand
the level of torque generated by the tool. Excessive torque
may cause breakage and possible personal injury.
1. Place the socket on the fastener head. Keep the tool
pointed straight at the fastener.
2. Press switch to start operation. Always check torque
with a torque wrench, as the fastening torque is
affected by many factors including the following:
a. Voltage: Low voltage, due to a nearly discharged
battery, will reduce fastening torque.
b. Socket size: Failure to use the correct socket
size will cause a reduction in fastening torque.
c. Bolt size: Larger bolt diameters generally require
higher fastening torque. Fastening torque will also
vary according to length, grade, and torque coefficient.
d. Bolt: Ensure that all threads are free of rust
and other debris to allow proper fastening torque.
e. Material: The type of material and surface finish
of the material will affect fastening torque.
f. Fastening time: Longer fastening time results in
increased fastening torque. Using a longer fastening
time than recommended could cause the fasteners
to be overstressed, stripped or damaged.
MAINTENANCE
Your STANLEY tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning. Your charger does not
require any maintenance apart from regular cleaning.
Warning! To reduce the risk of serious personal
injury, place the forward/reverse button in the lock-off
position or turn tool off and disconnect battery pack
before making any adjustments or removing/installing
attachments or accessories. An accidental start-up can
cause injury.
f Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
f Regularly clean the motor housing using a damp
cloth. Do not use any abrasive or solvent-based cleaner.
f Regularly open the chuck and tap it to remove any
dust from the interior.
f The charger and battery pack are not serviceable.
There are no serviceable parts inside.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
Warning! Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
Warning! Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Charger cleaning instructions
Warning! Shock hazard. Disconnect the charger from
the AC outlet before cleaning. Dirt and grease may be
removed from the exterior of the charger using a cloth or
soft non-metallic brush. Do not use water or any cleaning
solutions.
ENGLISH • 25