Troubleshooting Guide; Wiring Diagrams - Leviton PS110-1 Instrucciones De Instalación

El No de Cat. PS200 de Leviton, cubre 200° con compensación de
temperatura a un rango de hasta de 15 m (50 pies) máximo cuando el sensor
se monta a una altura de 3 m (10 pies). La unidad provee supresión de
sobretensión e inmunidad de RFI. También tiene un ajuste de nivel de luz de
ambiente que le permite una operación bajo un amplio rango de iluminación.
Los Sensores de Ocupación están diseñados para su uso en exteriores,
pero también se puede usar en interiores. Está adecuado especialmente
para montarse en paredes exteriores utilizando una caja rectangular NEMA
resistente a la intemperie.
Los Nos. de Cat. RS110, PS110 y PS200 están listados por UL, certificados
por CSA y cumplen con los requerimientos del Título 24 de California.
Figura 1 - Campo de Visión (Horizontal)
(No. de Cat. RS110 and PS110)
15 m
12 m
9 m
6 m
3 m
0
3 m
6 m
9 m
12 m
15 m
15 metros
Figura 2 - Campo de Visión (Vertical)
0
(No. de Cat. PS200)
15 m
12 m
9 m
6 m
3 m
110˚
0
3 m
6 m
9 m
12 m
15 m
15 mètres
12 m 15 m
max. max.
22
Set the Light Dial to the desired interval. Turning the dial fully counter-
clockwise sets the light level to the minimum of 5 LUX. Turning the dial fully
clockwise sets the light level to the maximum of 1000 LUX.
Temperature Compensation: These models have a built-in automatic
temperature compensator. This compensator automatically adjusts the
sensitivity (higher or lower) depending on the ambient outdoor temperature.
NOTE: Each Sensor is manufactured using strict quality control procedure and
rigorous testing before leaving the factory. If the unit performs erratically, follow
the steps below to determine the cause.
• Lights do not turn ON
- Check to see that power is ON at circuit breaker or fuse.
- Ensure that bulbs/tubes are good.
- Ensure wiring is correct per Wiring Diagrams.
- Ensure that Sensor is aimed properly.
- Check to see that lens is clean and unobstructed.
- Ensure any switch on the fixture is ON.
• Lights turn ON and OFF too quickly
- Ensure that no source of heat (i.e., lamps or vents) is too close to the
Sensor.
- Ensure that light is not reflecting back towards the Sensor from white
or reflective surfaces.
- Sensor may be more sensitive in winter than summer, due to sharper
contrast in Infrared.
200˚
• Lights do not turn OFF
- Check to see that time delay setting is at the minimum.
- Ensure that unit is firmly mounted on a stable surface that does not
sway in the wind.
- Ensure that Sensor is not aimed at swaying tree branches, a body of
water, air-conditioning or heater vents.
- Ensure that unit is not in the manual override mode by turning power
OFF for at least 5 seconds, then ON.
- If there is a switch in the circuit, make sure that it is in the proper
position.
- Check to see that the line voltage has not dropped below 100VAC (for
120VAC devices) due to the operation of a large appliance on the circuit.
• Lights turn ON in storms
Rain, snow and high winds can create changes in temperature that may
trigger the Sensor. False triggering can be minimized by installing the
Sensor in a protected location and by also turning down the sensitivity
control.
For additional information call Leviton's Technical Support Line.

TROUBLESHOOTING GUIDE

7