Cub Cadet RZT S Serie Manual Del Operador página 21

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

NOTE: This Operator's Manual covers several models. Tractor
features may vary by model. Not all features in this manual are
applicable to all tractor models and the tractor depicted may
differ from yours.
WARNING!
Before performing any maintenance or
repairs, disengage PTO, set parking brake, stop engine
and remove key to prevent unintended starting.
Engine
Refer to the engine operator's manual for all engine maintenance
procedures and instructions.
NOTE: Maintenance, repair, or replacement of the emission
control devices and systems which are being done at
owner's expense may be performed by any engine repair
establishment or individual. Warranty repairs must be
performed by a Cub Cadet Dealer.
Changing the Engine Oil
WARNING!
If the engine has been recently run, the
engine, muffler and surrounding metal surfaces will
be hot and can cause burns to the skin. Exercise
caution to avoid burns.
To complete an oil change, proceed as follows:
1.
Run the engine for a short time to warm the engine oil. The
oil will flow more freely and carry away more impurities.
Use care to avoid burns from hot oil.
2.
Locate the oil drain valve on the right side of the engine. See
Figure 6-1.
Oil Filler
Oil Drain Hose
Square-Head
Hose Plug
Figure 6-1
3.
Remove the hose from the retaining loop-clamp. Route
the free end of the oil drain hose toward an appropriate
oil collection container with at least a 2.5 quart capacity,
to collect the used oil. Remove the oil fill cap/dipstick from
the oil fill tube.
4.
While holding the free end of the oil drain hose over the oil
collection container, unscrew the square head hose plug
from the end of the hose. SeeFigure 6-1. Drain the engine
oil into the collection container.
Oil Fill Cap/Dipstick
Oil Fill Tube
5.
After draining the oil, wipe any residual oil from the oil
drain hose. Thread the square head plug into the drain
hose fitting and fully tighten the plug.
6.
Replace the oil filter, and refill the engine with new oil as
instructed in the engine operator's manual.
7.
Re-insert hose through the retaining loop-clamp.
Hydrostatic Transmission
The hydrostatic transmission is sealed at the factory and is
maintenance-free. The fluid level cannot be checked and the
fluid cannot be changed.
Battery
CALIFORNIA PROPOSITION 65 WARNING
Battery posts, terminals, and related accessories
contain lead and lead compounds, chemicals known
to the State of California to cause cancer and
reproductive harm. Wash hands after handling.
The battery is sealed and is maintenance-free. Acid levels cannot
be checked and fluid can not be added.
Always keep the battery cables and terminals clean and free
of corrosive build-up.
After cleaning the battery and terminals, apply a light coat
of petroleum jelly or grease to both terminals.
CAUTION:
If removing the battery for cleaning,
disconnect the NEGATIVE (Black) wire from it's
terminal first, followed by the POSITIVE (Red) wire.
When re-installing the battery, always connect the
POSITIVE (Red) wire its terminal first, followed by the
NEGATIVE (Black) wire. Be certain that the wires are
connected to the correct terminals; reversing them
could result in serious damage to your engine's
alternating system.
Cleaning the Tractor
Any fuel or oil spilled on the machine should be wiped off
promptly. Do NOT allow debris to accumulate around the cooling
fins of the engine, the transmission's cooling fan or on any other
part of the machine, especially the belts and pulleys.
Smart Jet™
Your tractor's deck is equipped with a water port on its surface as
part of its deck wash system.
Use the Smart Jet™ to rinse grass clippings from the deck's
underside and prevent the buildup of corrosive chemicals.
Complete the following steps AFTER EACH MOWING:
1.
Drive the tractor to a level, clear spot on your lawn, near
enough for your garden hose to reach.
CAUTION:
Make certain the tractor's discharge
chute is directed AWAY from your house, garage,
parked cars, etc.
2.
Disengage the PTO (Blade Engage), set the parking brake
and stop the engine.
3.
Thread the hose coupler (packaged with your tractor's
Operator's Manual) onto the end of your garden hose.
S
6 — M
ection
!
& a
aintenance
djuStMentS
21

Publicidad

Tabla de contenido

Solución de problemas

loading

Este manual también es adecuado para:

Rzt-s

Tabla de contenido