Settings Menu: Programming Alarms/Keypads; Fifth Part - Installation Of The Control Unit; Sixth Part - Technical Features; Technical Features Of Models Powered By Mains + Accumulator (5500-5502) - SILENTRON SILENYA HT 5500 Manual Del Usaurio

4.12) PROGRAMMING THE ALARM DEVICES/WIRELESS WARNINGS (SEE SPECIFIC INSTRUCTIONS)
a) Monodirectional sirens 5531 - alarm receivers (5051 - 5851) - load command receivers (5540 - 41-42): once powered, these
devices program themselves automatically on the first radio signal transmitted by the control unit.
b) Bidirectional 5530 sirens: programming reception takes place as described above but it is first necessary to programme their
transmission to the control unit on any alarm zone group which will be labelled "siren".
c) Keypad HT: to arm/disarm use that programmed codes on the control unit (see 4.8.2) - to connect one or more keypads to the control unit
and programme the PANIC key (!), proceed as follows:
connect the HT keypad to the power supply: All LED indicators will flash
within 60 seconds DISARM the control unit using its keys: the keypad LED indicators will turn off, confirming a successful connection. The
keypads already programmed can be re-programmed as follows.
Prepare the control unit on the PANIC zone and press the " !" key for 10 seconds , which has already been connected.

5) FIFTH PART - INSTALLATION OF THE CONTROL UNIT

All control units function by transmitting and receiving weak radio signals, as envisioned by the Standards in force: therefore they must be
installed on a wall using screws and rawplugs supplied, in situations that consent good propagation of these signals. Niches and/or columns
and/or reinforced concrete walls must be avoided as must metal cabinets. Avoid large metal surfaces and metal grids near to the control unit,
even if sunk into the wall. Positioning must consider the mandatory position of the detectors and sirens, making the control unit "central" with
respect to the former.
The quality of the signal received can be checked on the control unit (see 3.2.4 - B) and, if in doubt, this check must be performed before fixing
the control unit to the wall: operating with devices via radio of this type means knowing that often shifting of just a few centimetres can lead to
important improvement of the receiving-transmitting of signals.
The control unit must be preferably hidden from sight, but installed in a position where it is easy to use all functions, including vocal information:
for this reason the possibility to deport a speaker is envisioned. Places such as behind doors, behind wooden or plastic cabinets, behind
pictures and/or furniture. Avoid proximity with other electronic devices in general.
When the position has been defined, the connection wires must be made to converge (models 5500-5502), which must enter from the rear of
the device, if necessary sinking the inputs into the container. In particular, the cable carrying network voltage must be disconnected upstream
during installation (see 6.2).

6) SIXTH PART - TECHNICAL FEATURES

The technical features stated here can undergo variation without forewarning. If in doubt, consult the manufacturer's after-sales service and/or
the authorised distributors and dealers.
6.1 - MODEL 5500 SILENYA HT TOP GSM (DIAGRAM 4)- MODEL 5502 SILENYA HT TOP – TECHNICAL FEATURES
Note: the 5502 model does not have a GSM module and therefore does not feature GSM functions.
Power supply: 230V CA 50 Hz - 150mA – lack of mains power signalled after programmable time
Power ratings DC: total 1.2A – rated output 13 V DC
Battery envisioned: lead, hermetic, rechargeable 12V 2.2Ah standard. The batteries must have a
Consumption: 55mA in stand-by and no wired connections - 125mA with
Autonomy: approx. 36 hours with charged battery, in stand-by and without wired connections. To determine the autonomy in the
presence of wired connections, measure
External battery: an external battery can be connected to the clamps +AL and GND (max 12V 6Ah).
Alarm inputs via radio: up to 99 immediate, delayed or AND programmable detectors on the 3 alarm zone groups A-B-C
24-hour zone groups Panic, Robbery, Technical alarm.
wired: 6 NC (normally closed) lines, freely programmable on the 3 armed zone groups A B C
Anti-tampering via radio: reception of the tampering signal from each individual detector - reception of "operating status" signals and
flat battery signals (SUPERVISION).
wired: 3 NC Tamper lines (zones A B C) and protection against opening/removal of control unit
Alarm outputs: via radio: 72-bit codified digital transmissions per "alarm" - "outside alarm" - "full
"disarming" + 16 manageable coded commands
wired: 1 per 12V 0.5A siren command - 1 per 14V self-powered siren – 1 per siren on board –
NC/C/NO
Command inputs: 1 for connecting the additional electronic/electromechanical external key
RF noises: Continuous, simultaneous or programmable control of the two working frequencies
Events memory: last 200 events (new ones substitute the old ones)
Timed operations: programmable delayed arming – input delay programmable on every
programmable 24 h clock
Displays: Display 2 x 16 characters, with possibility of naming each single peripheral
Commands: 20-button alphanumeric keypad
Indoor siren: 106 db alarm siren
Acoustic signals: vocal messages for guide to installation and communication with the user + low intensity buzzer
RF emission: Quartz-controlled DualBand simultaneous frequency - factory programmed 72 bit digital codes with self-learning from
microprocessor- frequency and power in compliance with the law
Radio range: 100m in an open air without any background interference on the band - radio range cover can undergo large reductions
indoors due to the position of the devices in relation to the structure of the rooms.
Telephone part:
PSTN : connection with duplex cable and standard plug- self-adaptation of the features of the line in the country of use
through language change. Telephone book with 64 programmable numbers, 6 pre-recordable vocal messages.
GSM (5500) GSM Telit tetraband module with antenna. Telephone book, vocal messages management as above and SMS (6+11)
DIMENSIONS: 307 x 200 x 53mm - WEIGHT: 2.1 Kg - BOX: ByBlend - TEMPERATURE: operating/storage 10°+40°C
SILENTRON spa – 10139 – Via Sagra S.Michele 25 Torino - ITALIA
programmable via two relays for various functions
backlighting of the display - 500mA in alarm
the absorption of the battery (without 230V) and calculate it correctly.
detector - general alarm time 3 minutes fixed -
COPYRIGHT SILENTRON DS5500/1/2/3XC100120GM
class HB or higher casing
arming" - "partial arming"
on the
-
37