Troubleshooting - ADEMCO 998MX Instrucciones De Instalación

TABLE 1. INSTALLATION GUIDE FOR LENSES
STANDARD LENSES
PROTECTION RANGE
Mtg 15' 20' 30'
Height (4.6m) (6m) (9m) (12m) (15m)
8.5Ft -20° -16° -11°
(2.6m)
8Ft -20° -15° -10°
(2.4m)
7Ft -16° -12° -8°
(21m)
6Ft -13° -10° -6°
(1.8m)
–––– Vertical Pattern Setting –––––
LONG RANGE - 998-LR
PROTECTION RANGE
Mtg 20' 40' 60'
Height (6m) (12m) (18m) (24m) (30.4m)
8.5Ft -15° -9° -6°
(2.6m)
8Ft -14° -8° -6°
(2.4m)
7Ft -11° -6° -5°
(21m)
6Ft -8° -5° -4°
(1.8m)
Vertical Pattern Setting
* Important: When using the Long Range lens, set the
PIR for Instant response (Pulse Count 1).

TROUBLESHOOTING

PROBLEM CAUSE
Intermittent Rapid temper-
ature change.
Alarm
Check for electric
or gas heaters,
open flames, elec-
tric arcs, etc.
Drafts causing
drapes, light
fixtures, display
material to move
.
PIR does Polling loop volt-
not appear age supplied to
to be detector is
operating inadequate,
intermittent or
polarity reversed.
LED disable
LED
jumper is on
inoperative.
LED malfunc-
tion. Check for
broken or
shorted leads.
Detection Repositioned fur-
Area niture or equip-
Changes ment in the
protected area.
Mounting surface
is unstable. A few
degrees of
vertical shift can
change range
substantially.
Trouble Improper ID code,
Code or PIR serial No.
not entered.
PET ALLEY LENS– 998-PA
Mounting Height: 3 ft –3.5 ft (0.9–1m)
Vertical Pattern Setting (for all ranges): +4°
Important: Be sure to affix the provided masking
40' 50'
-8° -7°
-8° -6°
Regular maintenance and inspection (at least
annually) by the installer and frequent testing by
-6° -5°
the user are vital to continuous satisfactory opera-
tion of any alarm system.
-5° -4°
The installer should assume the responsibility of
developing and offering a regular maintenance
program to the user, as well as acquainting the
user with the proper operation and limitations of
the alarm system and its component parts.
Recommendations must be included for a specific
program of frequent testing (at least weekly) to
80' 100'
ensure the system's operation at all times.
-5° -5°
THE LIMITATIONS OF YOUR PASSIVE
-5° -4°
INFRARED MOTION DETECTOR
While the Intrusion Detector is a highly reliable
-4° -4°
intrusion detection device, it does not offer guaran-
teed protection against burglary. Any Intrusion
-3° -3°
Detection device is subject to compromise or failure
to warn for a variety of reasons:
• Passive Infrared Motion Detectors can only
detect intrusion within the designed ranges as
diagrammed in this installation manual.
• Passive Infrared Motion Detectors do not pro-
vide volumetric area protection. They do create
REMEDY
multiple beams of protection, and intrusion can
only be detected in unobstructed areas covered
Locate source and
reposition detector.
by those beams.
• Passive Infrared Detectors cannot detect motion
or intrusion that takes place behind walls, ceil-
ings, floors, closed doors, glass partitions, glass
Eliminate source of doors, or windows.
motion.
• Mechanical tampering, masking, painting or
spraying of any material on the lenses, windows
or any part of the optical system can reduce the
Assure that proper
detection ability of the Passive Infrared Motion
polarity is supplied and
that wiring is intact (no
Detector.
opens or shorts) and
• Passive Infrared Detectors sense changes in
connection secure.
temperature; however, as the ambient tempera-
Check for presence of
8–11V PP at terminals
ture of the protected area approaches the tem-
of unit. If too low, pol-
perature range of 90° to 105°F (32° to 40°C), the
ling loop run to control
detection performance can decrease.
may be excessive for
the wire gauge used, or
• This Passive Infrared Detector will not operate
polling loop current
without appropriate DC power connected to it, or
drain may be exces-
sive. Increase wire
if the DC power is improperly connected (i.e.,
gauge or add Polling
reversed polarity connections).
loop extender module
• Passive Infrared Detectors, like other electrical
to location in the loop
where voltage boost is
devices, are subject to component failure. Even
necessary and connect
though this equipment is designed to last as long
it to a power source.
as 10 years, the electronic components in it
Alternatively, the detec-
tor can be tested using
could fail at any time.
a 9-volt source (such
We have cited some of the most common reasons
as a 9-volt battery or a
9-volt power supply). that a Passive Infrared Motion Detector can fail to
catch intrusion. However, this does not imply that
Set LED disable DIP
these are the only reasons, and therefore it is rec-
switch to OFF.
ommended that weekly testing of this type of unit,
Return unit for
in conjunction with weekly testing of the entire
service.
alarm system, be performed to ensure that the
detectors are working properly.
Caution customer
Installing an alarm system may make the owner eli-
about layout changes.
Reposition detector. gible for a lower insurance rate, but an alarm sys-
tem is not a substitute for insurance. Homeowners,
Mount on
property owners and renters should continue to act
secure surface.
prudently in protecting themselves and continue to
insure their lives and property.
We continue to develop new and improved protec-
tion devices. Users of alarm systems owe it to
Set DIP swiitches1–7
themselves and their loved ones to learn about
to proper code, or
enter PIR serial No. these developments.
label over the look-down window.
TO THE INSTALLER
ADEMCO
SIX-YEAR LIMITED WARRANTY
Alarm Device Manufacturing
Division of Pittway Corporation, and its divisions,
subsidiaries and affiliates ("Seller"), 165 Eileen
Way, Syosset, New York 11791, warrants this
detector to be in conformance with its own plans
and specifications and to be free from defects in
materials and workmanship under normal use
and service for 72 months from the date stamp
control on the product. Seller's obligation shall
be limited to replacing, at its option, free of
charge for materials or labor, a detector which is
proved not in compliance with Seller's specifica-
tions or proves defective in materials or work-
manship under normal use and service. Seller
shall have no obligation under this Limited
Warranty or otherwise if the detector is altered or
improperly repaired or serviced by anyone other
than Ademco factory service. In case of defect,
return the detector to ADI or an authorized dis-
tributor for an immediate replacement.
THERE ARE NO WARRANTIES, EXPRESS OR
IMPLIED, OF MERCHANTABILITY, OR FITNESS
FOR A PARTICULAR PURPOSE OR OTHERWISE,
WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF. IN NO CASE SHALL
SELLER BE LIABLE TO ANYONE FOR ANY CON-
SEQUENTIAL OR INCIDENTAL DAMAGES FOR
BREACH OF THIS OR ANY OTHER WARRANTY,
EXPRESS OR IMPLIED, OR UPON ANY OTHER
BASIS OF LIABILITY WHATSOEVER, EVEN IF
THE LOSS OR DAMAGE IS CAUSED BY THE
SELLER'S OWN NEGLIGENCE OR FAULT.
Seller does not represent that its detector may
not be compromised or circumvented; that the
detector will prevent any personal injury or prop-
erty loss by burglary, robbery, fire or otherwise;
or that the detector will in all cases provide ade-
quate warning or protection. Buyer understands
that a properly installed and maintained alarm
may only reduce the risk of a burglary, robbery,
fire or other events occurring without providing
an alarm, but it is not insurance or a guarantee
that such will not occur or that there will be no
personal injury or property loss as a result.
CONSEQUENTLY, SELLER SHALL HAVE NO
LIABILITY FOR ANY PERSONAL INJURY,
PROPERTY DAMAGE OR OTHER LOSS BASED
ON A CLAIM THE DETECTOR FAILED TO GIVE
WARNING. HOWEVER, IF SELLER IS HELD LI-
ABLE, WHETHER DIRECTLY OR INDIRECTLY,
FOR ANY LOSS OR DAMAGE ARISING UNDER
THIS LIMITED WARRANTY OR OTHERWISE,
REGARDLESS OF CAUSE
SELLER'S MAXIMUM LIABILITY SHALL NOT IN
ANY CASE EXCEED THE PURCHASE PRICE
OF THE DETECTOR, WHICH SHALL BE THE
COMPLETE AND EXCLUSIVE
AGAINST SELLER. This warranty replaces any
previous warranties and is the only warranty
made by Seller on this detector. No increase or
alteration, written or verbal, of the obligations of
this Limited Warranty is authorized.
165 Eileen Way, Syosset, N.Y. 11791
Copyright © 1997 PITTWAY CORPORATION
N8023-5EN ( Part of N8023-5V1 8/99 )
Company, a
OR ORIGIN,
REMEDY