Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
TOP PANEL FEATURES
1.
POWER LED – Illuminates when the mixer is on.
2.
MIC GAIN – Adjusts the audio level of the
microphone signal.
3.
MIC
TREBLE
–
frequencies of the microphone channel.
Tip: If you experience feedback when using a
microphone at loud levels, try turning down the
high frequencies.
4.
MIC BASS – Adjusts the low (bass) frequencies of
the microphone channel.
5.
FX RETURN – Adjusts the audio level of the signal
sent through the FX RETURN inputs on the rear
panel.
6.
AUX INPUT – Adjusts the audio level of the signal
sent through the AUX IN inputs on the rear panel.
7.
CHANNEL GAIN – Adjusts the corresponding
channel's pre-fader and pre-EQ gain level.
8.
CHANNEL TREBLE – Adjusts the high (treble)
frequencies of the corresponding channel.
9.
CHANNEL
MID
frequencies of the corresponding channel.
10.
CHANNEL BASS – Adjusts the low (bass)
frequencies of the corresponding channel.
11.
CHANNEL BALANCE – Adjusts the balance of
right to left audio of the corresponding channel in
all outputs (MASTER, FX, and AUX / BOOTH
OUTPUTS).
12.
EQ -12dB / KILL SWITCH – Determines the range
of the CHANNEL EQ knobs. When pressed, the
lowest setting on the EQ knobs will be "zero" (a red
LED on the button will illuminate). When raised,
the lowest setting on the EQ knobs will be -12dB.
Note: The highest setting on all the EQ knobs is
always +12dB.
13.
INPUT SELECTOR – Selects the input source to be routed to the corresponding channel. Input jacks are located on the
rear panel.
14.
FX SEND – Selects whether the signal from the corresponding channel is routed to the FX SEND outputs.
•
OFF – The signal is sent directly to the CHANNEL FADER then to the
Program mix.
•
POST – The signal is sent to the CHANNEL FADER, then to the FX SEND
output, then to the FX RETURN input, then to the Program mix.
•
PRE – The signal is sent to the FX SEND output, then to the FX RETURN
input. This signal is then combined with the same signal sent directly to the
CHANNEL FADER. Both are then sent to the Program mix.
15.
CHANNEL FADER – Adjusts the audio level on the corresponding channel.
16.
LED METERS – Monitors the audio levels. The outer two meters monitor the levels of each channel. The inner two
meters monitor the Program mix.
17.
CROSSFADER – Blends audio between the channels assigned to the left and right side of the crossfader.
Note: The crossfader is user-replaceable if it should ever wear out. Simply remove the facepanel, then remove the
screws holding it in position. Replace the fader with a quality authorized replacement from your local Numark retailer
only.
18.
MASTER – Adjusts the output volume of the Program mix.
19.
AUX / BOOTH OUTPUT – Adjusts the audio level sent to the AUX / BOOTH OUTPUT on the rear panel. This signal is
identitcal to the MASTER OUTPUT.
20.
MASTER BUTTON – When pressed, this button sends the Program mix to the headphones (a red LED on the button
will illuminate). When raised, the Cue channel is sent to the headphones.
21.
CUE GAIN – Adjusts the volume level of the headphone output.
22.
CUE SLIDER – Previews the audio playing on Channels 1 and 2. Sliding this to the left plays Channel 1. Sliding to the
right plays Channel 2.
Adjusts
the
high
(treble)
–
Adjusts
the
mid-range
2
7
12
12
3
8
4
9
5
10
10
6
11
11
13
13
14
14
15
15
4
7
18
18
12
12
8
19
19
9
20
20
21
21
10
10
22
22
11
11
1
14
14
13
13
16
16
15
15
17
17
If nothing is connected to the FX
SEND or FX RETURN jacks, the
audio signal will be automatically
bridged between them. This way,
the signal will be uninterrupted if
the
FX
SEND
switch
accidentally engaged.
is
Publicidad
Tabla de contenido
