Front Panel Features - Numark CM200 USB Manual De Inicio Rápido

1. Power LED: Illuminates when the mixer is
on.
2. Mic ON/OFF: Toggles activation of the DJ
Mic.
3. Mic Gain: This knob adjusts the volume of
the microphone input.
4. Mic Bass: This knob adjusts the low-tone
of the microphone.
5. Mic Treble: This knob adjusts the high-
tone of the microphone.
6. XLR/¼" Combo Microphone Input
Jack: Connect your DJ mic at this location.
7. Channel Gain: This rotary control adjusts
the pre-fader input level.
8. Channel Treble: This rotary control
adjusts the high-tone level.
9. Channel Middle: This rotary control
adjusts the middle-tone level.
10. Channel Bass: This rotary control adjusts
the low-tone level.
11. Input Selector: This toggles select what
input source is routed to the channel from
the rear panel connected units.
12. Channel Fader: This slide fader is used to
adjust the level sent to program mix.
13. Cue Button: pressing this button sends
post gain, post EQ, and pre channel fader
level audio the PFL "Pre–fader level" section
of the headphone cue.
14. Headphone Volume: This rotary control
adjusts the volume level of the headphone
output.
15. Headphone Mix: Program level and PFL
(CUE) signal levels can be mixed by this
slider. When all the way left, audio heard
will be determined by Cue Button
selections. When all the way right final
only (PGM) program mix audio will be
heard.
16. Split/Blend Button: When in the down
position, headphone audio will be split so
mono PFL audio is in the left ear and mono
PGM audio is in the right ear. When the
button is up, stereo PFL and PGM audio will
be mixed (blended).
17. Headphone Jack: Your headphones can
be connected to this ¼" terminal. The
volume should always be set at its lowest
setting while connecting and disconnecting
headphones to prevent damage to
headphones and/or your hearing.
18. Replaceable Crossfader: This slide fader
blends audio between the channels
assigned to the left and right assign
switches.
Note: This fader is user replaceable if it
should ever wear out. Simply remove the
All manuals and user guides at all-guides.com

FRONT PANEL FEATURES

facepanel and then remove the screws
holding it in position. Replace the fader
with a quality authorized replacement from
your local Numark retailer.
19. Assign Knob: Rotary position determines
which input channel will be heard when the
crossfader is moved towards this knob.
Volume levels of channels not selected will
be determined only by the individual
channel sliders.
20. Fader Start: activates the crossfader to
send play and cue digital pulse commands
to your auto-start Numark CD player or
other popular brand. For fader start, attach
your mixer to a remote start CD player
using industry standard 1/8"(3.5mm)
cables. When you move the crossfader
toward the active channel, the attached CD
player will start. When it is moved away,
that side will cue (similar to pressing the
cue button) or stop depending upon brand
of CD player.
21. Master Slider: This control adjusts the
main output volume using the PROGRAM
audio as a source.
22. Stereo/Mono toggle: adjusts the Master
output for stereo or mono operation.
23. Panning: adjusts the balance of right to
left audio in all outputs (Master, Record,
Zone).
24. Meter Assign: determines whether PFL or
post master level audio is sent to the
stereo LED meter.
25. Stereo Level Indicator: quickly and
accurately tracks level of audio sent to it.
When using as a master output meter,
set the crossover, equalizer and power amp
inputs to avoid distortion at each step in
the audio chain. Proper attention to the
peak meter results in the punchiest
possible sound without audible distortion.
When used to adjust the PFL levels, PFL
cue signal is sent to the meter through the
cue assign buttons. Accurately match
channel levels with the Pre-fader gain and
EQ controls before mixing them together.
The idea is to properly match PFL inputs,
not the input with the stereo output meter!
26. Booth/Zone Fader: controls volume for a
remote zone or booth monitors using
PROGRAM audio as a source.
Note: This could also be used to supply line
level audio to a lighting controller or to
lights that are sound activated.