RS V10745 Hoja De Instrucciones página 6

V10745
14
A
VR1=100KΩ
100K
10K
1K
100
10
1
100p
A. Required base speed (Hz)
B. C-freq (F)
A. Geforderte
Grundgeschwindig-keit
B. C-freq (F)
A. Velocidad base requerida
(Hz)
B. C-frec (F)
A. Choisi vitesse de base
requise (Hz)
B. Fréquence C (F)
15
A
100
10
1
0.1
A. Max speed/base speed
B. VR1+10KΩ/R-freq
A. Verhältnis Grund-/
Höchstgesch-windigkeit
B. VR1+10KΩ/R-freq
A. Velocidad
máxima/Velocidad base
B. VR1+10KzΩ/Rfrec
A. Vitesse max./vitesse
de base
B. VR1+10 kΩ/fréquence R
6
VR1=0Ω
VR1=1MΩ
1n 10n 100n
1µ
B
A. Velocità richiesta (Hz)
B. C-freq (F)
DK
A. Krævet grundhastighed
(Hz)
B. C-frekv (F)
NL
A. Vereist basistoerental
(Hz)
B. C-freq. (F)
SE
A. Erfordrad grundhastighet
B. C-frekv. (F)
1 10 100
B
A Velocità max./velocità
base
B. VR1+10KΩ/R-freq
DK
A. Max. hastighed/
grundhastighed
B. VR1+ 10KzΩ/Rfreq
NL
A. Max. toerental/
basistoerental
B. VR1+ 10KzΩ/Rfreq
SE
A. Max. hastighet/
grundhastighet
B. VR1+ 10KzΩ/R-frekvenbs
Figure 1
A. If using common supplies (≤24V)
B. Motor supply (+15V to +36Vdc)
C. Phase A output
D. Phase A' output
E. Phase B output
F. Phase B' output
G. Sync input/output
H. Home output
I. Direction (CW/CCW)
J. Step pulse input
K. Full/half step input
L. Reset input
M.Output disable input
N. Current program input
O. Overload output
P. Overtemperature output
Q. VCO speed control input
R. VCO pulse output
S. VCO base speed input
T. VCO run/stop input
U. Where fitted
V. Auxiliary +12V output (50mA maximum)
W.Auxiliary +5V output (50mA maximum)
X.Logic supply (+15 to +24Vdc)
Y. 0V common
Specifications
Bipolar stepper motor drive with optional thermal protection and on
board oscillator.
Electrical
Motor supply:
+15 to 36Vdc (+10% max.) smoothed unregulated.
Logic supply:
+15 to 24Vdc (+10% max.) smoothed unregulated.
Note: The motor and logic may share the same power supply up to +
24V or up to +36V if a suitable dropper resistor is fitted in the
logic supply line.
Auxiliary outputs (available for external circuitry):
+ 12V regulated 50mA maximum
+5V regulated 50mA maximum
Motor drive output:
Biopolar chopped constant surrent with overload protection. Suitable
for driving hybrid or permanent magnet stepper motors with 4,6 or 8
leads.
Maximum output current 3.5A per phase. Output current set by on-
board DIP switches or external programming resistor.
Control Inputs:
CMOS schmitt trigger inputs operating at +12V with 10kΩ pull-up
resistors and diode isolation.
Logic 0 (low) - 0V to +2V or contact closure to 0V.
Logic 1 (high) - +9V to +30V maximum or open circuit.
Monitor outputs:
Open collector NPN transistor, reference to 0V.
Low level - +1V maximum at 30mA maximum.
High level - open circuit +24V dc maximum.
RS Stock No.
255-9065