10
TROUBLESHOOTING
Check the following before assuming there is a problem with the set.
1. Are all connections proper ?
2. Is the set being operated as described in the operating instructions ?
3. Are the speakers and input components being operated properly ?
If the set does not seem to be operating properly, check the points listed below. If these points do not apply, the set
may be damaged. Turn off the power immediately and contact your store of purchase.
Symptom
Cause
POWER LED does not
• Power supply co d is not connected.
light and no sound is
produced when POWER
switch is turned on.
• Speaker
cords
connected.
POWER LED lights but no
• INPUT SELECTOR not set to proper
sound is p oduced.
position.
• VOLUME control turned down.
• Speaker cords not properly con-
nected.
Sound is not produced
• Input cords not properly connected.
from one side only.
• Left/right
balance
adjusted.
Volume level is different
• Tuner and record outputs different.
when listening to tuner
and records.
Positions of instruments
• Left and right speakers or input
inverted for stereo sources.
cords inverted.
• Turntable's
ground
connected.
Booming sound produced
• Input cords not properly connected
when playing records.
to PHONO terminals.
• Influence from a TV or o her
electrical device near the turntable.
• Turntable and speaker systems are
too close.
Howling produced when
• Floor is soft and v brates easily.
volume is turned up while
playing records.
• Stylus pressure is too light.
Sound is distorted.
• Dirt on tip of stylus.
• Defective cartridge.
• Batteries dead.
• Remote control unit too far f om this
unit.
This unit does not operate
• Obstacle between his unit and
p operly when remote
remote cont ol unit.
cont ol unit is used.
• Different button is being pressed.
• < and > ends of battery inserted in
reverse.
Remedy
• Check hat he cord is plugged in.
not
p operly
• Connect securely.
• Set to the proper position.
• Set to an appropriate level.
• Connect securely.
• Connect securely.
imp operly
• Adjust he BALANCE cont ol.
• Adjust he tuner output to he
turntable's output (if he tuner is
equipped wi h an output cont ol).
• Check he left/right connections.
wire
not
• Connect securely.
• Connect securely.
• Change he position of installation.
• Move speaker systems as far away
as poss ble.
• Use cushions to absorb
v brations transmitted f om the floor
to the speakers. If he turntable does
not include insulators, use audio
insulators, available in stores.
• Apply p oper pressure.
• Check he tip of he stylus.
• Replace the cartridge.
• Replace w th new batteries.
• Move closer.
• Remove obstacle.
• Press the proper button.
• Insert batteries properly.
11
SPECIFICATIONS
2
POWER AMPLIFIER SECTION
Rated Output Power:
Output terminals:
• PRE AMPLIFIER SECTION
Rated Output:
Input Sensitivity/
Input Impedance:
page
RIAA Deviation:
5, 7
• OVERALL CHARACTERISTICS
SN Ratio (IHF A Network):
Frequency Response:
5, 6
Tone Control Adjustable Range:
9
9
6
• OTHERS
Power Supply:
5
Power Consumption:
10
Dimensions:
—
Mass:
• REMOTE CONTROL UNIT (RC-906)
Remote control system:
Power supply:
5, 6
External dimensions:
5
Mass:
5
* Maximum dimensions include controls, jacks, and covers.
—
(W) = width,
(H) = height,
• For improvement pu poses, specifications and functions are subject to change without advanced notice.
—
he
—
—
—
—
7
8
8
8
7
50 W + 50 W (4 Ω/ohms, DIN, 1 kHz, T.H.D. 0 7%)
4 to 16Ω/ohms
150 mV (Recout Terminal)
PHONO:
2.5 mV/47 kΩ/kohms
CD, TUNER, DVD/AUX,
TAPE, MD, AUX-2:
100 mV/16 kΩ/kohms
PHONO:
20 Hz to 20 kHz ±0.5 dB
PHONO: 80 dB (at 5 mV input) (input terminals short-ci cuited)
CD, TUNER, DVD/AUX,
TAPE, MD, AUX-2: 102 dB (SOURCE DIRECT: ON)
5 Hz to 100kHz : +0, -3 dB (SOURCE DIRECT: ON)
BASS:
100 Hz ±8 dB
TREBLE:
10 kHz ±8 dB
LOUDNESS: 100 Hz +6 dB
10 kHz +4 dB
AC 230 V, 50 Hz
110 W
Approx. 1W in standby mode)
250 (W) X 90 (H) X 371 (D) mm
6 0 kg
Infrared pulse system
3 V DC, Two size R03 ("AAA")
dry cel batteries
48 (W) X 210 (H) X 29 (D) mm
120 g
(including batteries)
(D) = depth
ENGLISH
11