Operation - Denon PMA-201SA Instrucciones De Operación

8

OPERATION

(1) Playback
8
VOLUME
¡
ON / TA DBY FF MODE OU CE D RE T
PH NES FU CT ON
NTEG ATED A
3 4 2,6
OFF ON
3
SYSTEM
POWER
PROG /
D RECT
STOP PLAY
VOLUME
/SELECT
PRESET
+
6
-
TAPE
SLEEP FUNCTION MODE
4
CD
TUNER
MD
1
Check that all connections are correct.
Turn the volume control
VOLUME
fully counterclockwise
( . ) to set the volume to
2
the minimum.
(Main unit)
Turn on the power.
• The indicator first flashes red, then turns
green and stops flashing (remaining lit).
™ ¡ ON
ON / STANDBY OFF
SYSTEM
POWER
(Main unit) (remote cont ol unit)
2 Power on/standby mode and function
3
memory
B When the remote control unit is used to
turn the PMA-201SA's power on from the
standby mode, the function is set to the
function that was selected when the
power was last set to the standby mode.
(Last memory function)
B If the function has been cleared f om the
memory, the function is set to "CD" when
the PMA-201SA's power is turned on.
E ther turn the FUNCTION dial on the main unit
or press the remote cont ol unit's FUNCTION
button to select the function source to be
played.
• The function switches in the order shown
below.
✻ The function switches in the opposite order
when the dial is turned counte clockwise .).
L F ER PMA 01 A
4
FUNCT ON
FUNCTION
(Main unit) (remote control unit)
CD TUNER
MD TAPE AUX 2
Start playback of the selected function sou ce.
5
• For instructions on operation, refer to the
component's operating instructions.
Adjust the volume.
VOLUME
6
(Main unit) (remote control unit)
Adjust the BALANCE, BASS, and TREBLE
controls and set the LOUDNESS position to the
7
desired position.
✻ For instructions on adjusting, see "(2) Setting
the various modes" on page 9, 10.
To use the source direct function:
Set the SOURCE DIRECT button to the "ON"
position.
8
(2) Setting the various modes
[1] Adjusting the bass and treble
N / S AN BY ¡ O F M DE
PHO ES UN T ON
2 1
STOP PLAY
PRESET
+
-
TAPE
SLEEP FUNCT ON
Press the MODE button to display the mode to
DVD/AUX
be adjusted ("BASS" or "TREBLE").
PHONO
MODE
(Main unit)
• The mode switches as follows each time the
button is pressed:
1
BASS
Playback
function source
✻ When the source direct mode is on, the mode
VOLUME
switches as shown below (the BASS and
/SELECT
TREBLE adjustment modes cannot be
selected).
SPEAKER
Either turn the FUNCTION dial on the main unit
or use the remote control unit's SELECT
buttons.
FUNCT ON
(decrease)
(Main unit)
2
• To increase the bass or treble:
Turn the dial clockwise (,) or press the
button.
To decrease the bass or treble:
Turn the dial counte clockwise .) or press
SOURCE DIRECT
H
the button.
• The bass and treble can be adjusted within
the range of –12 to 0 to +12 in steps of 2.
The response is flat at 0.
(Main unit)
[2] Setting the loudness mode
VOLUME
OUR E D RECT N / S A DBY ¡ FF ODE
PH NES UN T ON
NTEGRA ED AMPL F ER MA 01SA
2 1
VOLUME
/SELECT
2
MODE
1
Press the MODE button to display
"LOUDNESS".
MODE
1
(remote control unit)
• The mode switches as shown at the left each
time the button is pressed.
✻ "LOUDNESS" cannot be selected when the
TREBLE LOUDNESS
source direct mode is on.
SPEAKER BALANCE
Either turn the FUNCTION dial on the main unit
or use the remote control unit's SELECT
buttons.
Playback function source
(OFF)
2
VOLUME
/SELECT
(increase)
(increase)
• To set to "ON":
Turn the dial clockwise (,) or press the
button.
(decrease)
To set to "OFF":
(remote control unit)
Turn the dial counte clockwise .) or press
the
D
NOTE:
The maximum total volume increase for the bass,
treble and loudness together is +12. If for example
the bass and treble are set to +12, the sound does
not change when the loudness function is turned on
and off.
ENGLISH
VOLUME
OUR E D RE T
NTEGR TED AMPL F ER MA 01SA
STOP PLAY VOLUME
/SELECT
PRESET
+
2
-
TAPE
SLEEP FUNCT ON MODE
1
MODE MODE
(Main unit) (remote control unit)
VOLUME
SELECT
(ON)
FUNCTION
(ON)
(OFF)
(Main unit) (remote control unit)
D
H
button.
9