General Overview; Preparatory Works - BQS BCAFIX 123 Manual De Uso

16. instruction illustrations are for informational purposes only. The child
restraint system may contain small differences compared to the
photographs or images in the instruction manual.

1. GENERAL OVERVIEW

A. Headrest.
B. Diagonal belt guides. Group 2/3.
C. Shoulder pads.
D. Harness straps.
E. Harness buckle.
F. Harness adjustment button.
G. Harness adjustment strap.
H. Reclining lever.
2. VEHICLE INSTALLATION POINTS
WHERE:
In the vehicle rear seats.
* Please, do NOT install the safety seat in forward seats except for the
following cases:
1. Whenever the vehicle does not count with rear seats.
2. When all rear seats are already occupied by children exceeding
135 cm height.
3. When it is not possible to install all child restraints systems in the rear seats.
*note: According to Spanish legislation for child restraint systems (Royal Decree 667/2015).
HOW:
Install rearward facing.
GROUP 1 • (optional) Install forward facing.
GROUP 2/3 • Install forward facing.
In seats with:
iSoFiX anchorages (between seat and backrest) and Top Tether anchor points
(eg in the tray, on the floor or behind the backrest) and 3-point belt (vehicle belt).
NOtICE:
The child seat must only be used in this seat IF it has a lap and diagonal
belt (3 points).
24
I. Headrest height regulator.
J. Harness Height adjuster.
K. installation manual bin.
L. isofix arms.
M. isofix arms unlocking button.
N. Abdominal belt guides
O. Diagonal belt locking lever.
P. isofix adapters.
1
2
BCA 123

3. PREPARATORY WORKS

3.1 Prepare ISOFIX
1. if your vehicle is not equipped with the iSoFiX insert guides as standard, clip
the two insert guides 02 which are included with the seat with the cut-out
facing upwards onto the two iSoFiX attachment points 01 of your vehicle.
tIP: The iSoFiX attachment points are located between the surface and the
backrest of the vehicle seat (fig.1).
2. Pull the fabric loop (03) to pull out both locking arms to longest position (fig.2).
3.2 Adjusting the headrest in 5-point harness installation. Group 1
A correctly adjusted headrest (07) ensures optimal protection for your child
in the safety seat:
The headrest (07) must be adjusted so that the shoulder belts (08) are at the
same level as your child's shoulders (fig.3).
CAUtION! The shoulder belts (08) must not run behind the back of the
child or at ear height or above the ears.
The shoulder belts are adjusted as follows:
1. Press the adjusting button (26) and at the same time pull both
shoulder belts (08) forwards. Do not pull on the shoulder pads (19),
loosen the 5-point harness of the child seat as mush as possible (fig.4).
Back side of the child seat:
2. Press the button of the shoulder belt height adjuster (10) at the rear of the
seat shell and tilt the shoulder belt height adjuster (10) towards you.
3. Slide the shoulder belt height adjuster (10) to select the correct height of
the shoulder belts (08) and engage it in the position that fits for your child
by releasing the button (fig.5).
3.3. Adjusting the headrest in vehicle belt installation. Group 2/3
A correctly adjusted headrest (07) ensures that the diagonal seat belt section
(11) is optimally positioned, and gives your child the optimal protection.
The headrest (07) must be adjusted so that there is a space two fingers wide
between the headrest (07) and your chidl's shoulders (fig.6)
To adjust the height of the headrest to fit your child:
1. Squeeze the adjustment handle (12) on the back of the headrest (07). This
unlocks the headrest (fig.7).
2. You can now move the unlocked headrest (07) to the desired height. As
www.babyqs.com
25