Campingaz 2 Serie Instrucciones De Empleo página 10

Handle the lid carefully, especially during operation. Do not
lean over the base.
F. CHECKING FOR GAS LEAKS
Important: Never use a naked flame to check for gas leaks.
1. Work outside, away from all sources of ignition. Do not
smoke.
2. Make sure the control knobs are in the "off" (O) position.
3. Connect the flexible hose to the connector and appliance as
described in Section D.
4. Fit the regulator onto the gas cylinder in accordance with its
instructions.
5. Use a gas leak solution to test for leaks.
6. (Fig. 5 A) Apply the solution to the connections cylinder/
regulator/hose/appliance.
7. Open the gas cylinder valve (the control knobs should
remain closed: off position (O)). Bubbles in the gas leak
solution indicate that there is a gas leak.
8. The leak can be stopped by tightening any hose connection
or replacing any faulty component. The appliance must not
be used until the leak is stopped.
9. Close the valve on the gas cylinder.
Important:
Check for leaks at least once per year and each time the gas
cylinder is replaced.
G. PRIOR TO USE
Never use the appliance until the instructions have been read
carefully and understood. Additionally, ensure that:
y There are no leaks.
y (Fig. 6) The venturi tubes (VT) are not blocked (example:
Cobwebs)
GB
y (Fig. 5 B) The hose does not touch any components which
may get hot.
y The ventilation openings in the cylinder storing compartment
(if present) are not obstructed.
y The grease trap(s) is (are) correctly inserted into its (their)
compartment and that it (they) is (are) correctly positioned,
as far as it (they) will go.
y The heat reflector is correctly installed at the bottom of the
firebox.
y The firebox's 6 removable parts are reinserted (see Section
O Cleaning and maintenance).
H. LIGHTING THE BARBECUE BURNERS
Never light the appliance with the lid closed, only with the lid
opened.
1. (Fig. 7 A) Open the cooking lid.
2. (Fig. 7 B) Make sure that the control knobs are in the "OFF"
position (O).
3. Open the gas cylinder valve.
4. (Fig. 8 A) Push and turn the control knob of the desired
burner counterclockwise to position (
ignition button ( ).
5. If your barbecue is equipped with a piezoelectric
igniter:
y (Fig. 8 B) Press immediately on the igniter button (
until it clicks.
y If the burner does not ignite after 4 or 5 attempts, wait 5
minutes and then repeat the operation.
6. If your barbecue is equipped with an electronic spark
igniter:
y (Fig. 8 B) Press immediately on the switch (
of sparks occurs. Continue pressing for a few seconds
until the burner is lit.
y If the burner does not ignite after 4 or 5 attempts, wait 5
minutes and then repeat the operation.
7. Adjust the flame to the desired height by turning the control
knob between (
8. Do the same for all the burners.
9. If the electronic ignition system does not work, light the
barbecue manually (next paragraph).
I. LIGHTING THE BARBECUE MANUALLy
1. Open the cooking lid.
2. Make sure that the control knobs are in the "OFF" position
(O).
3. Remove one of the cooking grids to gain access to the
burners.
4. Turn on the gas supply (valve or lever on the regulator).
5. (Fig. 8 C) Put a lighted match in front of the burner.
6. (Fig. 8 A) Push and turn the control knob to the desired
burner counterclockwise to position (
7. Adjust the flame to the desired height by turning the control
knob between (
Once the burner is lit, replace the grid or griddle.
J. ExTINGUISHING THE BARBECUE
(Fig. 7 B) Return the control knobs to the "off" position (O), then
close the cylinder valve.
K. LIGHTING THE SIDE BURNER
(DEPENDING ON THE MODEL)
The side burner may operate independently or in conjunction
with the barbecue burner. Before igniting the side burner, be
sure that the lid is opened and then tucked away (Fig. 9A, B).
Lighting:
1. Open the gas cylinder valve.
2. (Fig. 5 A)Check that there is no gas leak between the gas
cylinder and the side burner.
3. Check the condition of the hose connecting the grill burner
to the side burner. If there are signs of cracks, call our after
sales service to have it replaced.
4. (Fig. 9 C) Press and rotate the control knob on the side
burner (
5. (Fig. 9 D) Press the ignition button ( ) until the burner lights.
If the burner does not light after 10 seconds, put a match to
the edge of the burner.
6. Adjust the flame to the dimensions of the recipient by using
the two flow positions: HIGH (
use recipients with a diameter less than 10 cm or over 24
cm.
L. TURNING OFF THE SIDE BURNER
(DEPENDING ON THE MODEL)
Return the control knob (
close the valve on the gas cylinder if the appliance is not in use.
To close the lid, slide it in its grooves, pulling it upwards until it
). Press the
reaches the spindle, then tip it forwards.
M. REPLACING THE GAS CyLINDER
1. Always work in a well ventilated area and never in the
) presence of a flame, spark or heat source.
2. Return the control knobs to the "off" position (O) (Fig. 7 B)
then close the cylinder valve.
3. Remove the regulator, check that the sealing joint is in good
condition.
4. Put the full cylinder in place, refit the regulator, taking care
). A burst
not to apply stress to the hose.
5. Check for gas leaks according to Section F.
10
) and ( ).
) and ( ).
) to its FULL FLOW position (
) or LOW (
) to the OFF (O) position, then
).
).
). Do not