Cequent Performance Products Chevy Spark 1LS Instrucciones De Instalación

Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24893F
Wrenches: 11/16", 7/8"
Drill Bits: 1/2"
0.563 (14.30 mm)
Note: Drill rearward
of existing 3/4"
diameter hole
in frame rail
Figure 1: Access hole modification to allow
pull wiring of block and carriage bolt
B. Align block on
A. Insert bolt and
access hole
Block into frame
Figure 2: Pull Wire Procedure
j
7/16"-14 x 1.50" Carriage Bolt GR.5
Qty. (2)
k
3" x 7/8" Block
Qty. (2)
l
7/16" Conical Washer
Qty. (2)
m
7/16"-14 Hex Nut GR. 2
Qty. (2)
1. Lower the exhaust by removing the rubber exhaust isolator located above the muffler.
Use 1/2" drill to enlarge the existing 3/4" holes on both frame rails as shown in Figure 1.
2.
Install 7/16" carriage bolts and 7/8" blocks using the reverse pull wire procedure shown in Figure 2. Leave pull wires attached.
3.
4. Raise hitch into position and feed pull wires through the holes on the hitch brackets, remove pull wires, and loosely install
fasteners as shown in Figure 3.
Install the 1/2" carriage bolt and 2" x 2" spacer to tie down hook as shown in Figures 3 & 4. Do not tighten down at this point.
5.
6. Center the hitch on the vehicle and torque all fasteners to the specifications shown below.
7. Reinstall exhaust.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2012 Cequent Performance Products, Inc.
Installation Instructions
Fascia
Chevy Spark 1LS/1LT
Drawbar Kit:
3599
Drawbar must be used in the
RISE position only.
j
k
l
m
Tie down hook
C. Pull bolt thru
block
Pull Wire
Tighten all 7/16"-14 fasteners with torque wrench to 50 Lb.-Ft (68 N-M).
Tighten all 1/2"-13 fasteners with torque wrench to 75 Lb.-Ft (102 N-M).
Do Not Exceed Lower of Towing Vehicle
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, PC4
Note: Orientation of Block
n
o
p
q
Figure 3: Hitch Installation
n
1/2"-13 x 1.75" Carriage Bolt GR.5
Qty. (1)
o
2" x 2" Spacer
Qty. (1)
p
1/2" Conical Washer
Qty. (1)
q
1/2"-13 Hex Nut GR. 2
Qty. (1)
Sheet 1 of 3 24893N
Part Numbers:
24893
60312
77281
Manufacturer's Rating or
Tie down hook
Figure 4: Back view of
properly Fastened
To Tie Down Hook
j
k
l
m
8-6-12
Hitch
Rev. A