Technical Specifications - RIB K 2007 Manual De Usario

Ocultar thumbs Ver también para K 2007:

Manual del usuario (32 páginas)

Contenido

Tabla de contenido

Idiomas disponibles

It is necessary to request a K2007 control panel with firmware 11 NOUP.

Select the automatic functioning DIP 6 OFF.

It can be done by connecting a switch and/or a daily/weekly clock either in parallel to the K

BUTT button or instead of the K BUTT button. When the control board receives this command,

the gate will open and by keeping this contact closed for all the time of the gate opening, the

Clock Function is automatically activated. In fact, once reached the open position, the gate

will remain opened and all of the control board functions are blocked. Only when K BUTT

contact is released, the control board functions are re-activated and the Automatic Closing

restarts (if enabled) doing the countdown to the gate closing.

PEDESTRIAN command (PED BUTT - COM)

This command is useful to open the gate partially, just enough, for example, to permit

a pedestrian crossing. In fact, the Pedestrian command (see Point E) is carried out only

by opening the gate just enough for a pedestrian to pass, as described into the Point E

procedure.

From the Pedestrian opening position the Automatic Closing can be enabled or disabled

with DIP3.

From the Pedestrian opening position, the gate can be completely opened by the OPEN or by

the K BUTT button or by the RADIO button.

AUTOMATIC CLOSING (from the COMPLETE open position)

The Automatic Closing from the complete open position can be enabled turning ON the DIP3.

The maximum gap of time that can be programmed is 5 minutes (see Point D).

AUTOMATIC CLOSING (from the PEDESTRIAN open position)

The Automatic Closing from the pedestrian open position can be enabled turning ON the

DIP3. The maximum gap of time that can be programmed is 5 minutes (see Point E).

FUNCTIONING OF SAFETY ACCESSORIES

PHOTOCELL (PHOT - COM)

In case the switch DIP4 is in the OFF position, the photocells are active both in gate opening

and in gate closing. In this configuration, if an obstacle cuts the photocell beam:

- while the gate is closing, the gate will open

- while the gate is opening, the gate will stop and will restart opening when the obstacle is

removed

- while the gate is still, it will not move neither in opening nor in closing.

In case of the switch DIP4 is in the ON position, the photocells are active only in gate closing.

In this configuration, if an obstacle cuts the photocell beam:

- while the gate is closing, the gate will open

- while the gate is opening, the gate will continue open

- while the gate is still, it will open if a open command is request, it will remain still if a close

command is request.

The photocell input (PHOT - COM) is a NORMALLY CLOSED contact.

In case there are more couple of photocells, the contacts from all the photocell receivers

must be connected in series.

In case the photocells are not installed, this contact must be short circuited with a wire jump

(from PHOT to COM) to permit the gate to operate.

SAFETY STRIP (EDGE - COM)

If it intervenes during opening, it inverts the movement and closes for 2 seconds and then

stops.

If it intervenes during closing, it inverts the movement and opens for 2 seconds and then

stops.

If the safety strip remains engaged (NO contact), no automatic movement is allowed.

In case the safety strip is not installed, this contact must be short circuited with a wire jump

(from EDGE to COM) to permit the gate to operate.

PAY ATTENTION: it is highly recommended to check safety-strips operation at least every

6 months.

SAFETY STRIP ALARM

After the inversion given by the intervention of the safety edge, the gate stops in alarm mode

and this is signaled by the blinker on for 1 minute and by the buzzer on for 5 minutes.

During or after the minute of alarm, the normal gate operations can be restored by pressing

any push button.

TESTING THE SAFETY STRIP equipment

The DIP10 ON enables to test the safety strip equipment. The test is performed every time the

gate completes a full opening. The test is available only if the safety strip device is equipped

with a dedicated power supply input.

In fact, the safety strip equipment power supply input can be connected to the A+TEST and

A- outputs (DIP10 ON). Automatically, every time the gate completes a full opening, just

before closing, the control board switches OFF the A+TEST and A- power supply output for a

very short time. While the safety strip power supply is switched OFF, if everything is working

fine the safety strip contact (EDGE - COM) must open. In case the test fails, no other gate

manoeuvre will be allowed and the alarm state will be signalled by both the Blinker and the

Buzzer, if installed, which will remain on for 5 minutes

NOT ALL THE SAFETY STRIPS CAN BE TESTED, THUS THE SWITCH DIP10 MUST BE LEFT

OFF.

STOP BUTTON

If the Automatic command is enabled (DIP 6 OFF), a Normally Closed contact could be

connected in series to the COM wire of the opened and the closed limit switches.

This contact works like a STOP button to interrupt any gate manouver.

FUNCTIONING IN DEAD MAN MODE WHEN THE SAFETY DEVICES ARE FAILING

If the safety edge fails or remains engaged for more than 5 seconds, or if photocell fails or

remain engaded for more than 60 seconds, the K BUTTON and PEDESTRIAN commands will

work only in dead man mode.

The signal that this mode has been activated is given by the blinking of the programming led.

With the blinking of the programming led, the opening and closing operation are allowed

only with the command button pressed and held. The radio commands and that of automatic

closing, will be excluded, since their use in this mode, is not allowed by the norms.

Once the failing safety device is repaired, in automatic after 1 second, all standard

commands that were selected, such as step by step, automatic mode, radio commands and

automatic closing start functioning again.

Note 1: during this functioning in dead man mode, in case of damage to the safety strips

(or photocells) the photocells (or safety strips) still work by interrupting the operation

in progress.

The dead-man operation is only an emergency operation which must be activated

for a very short period and with the complete installation at sight so to have a

secure and safe control of the system. As soon as possible however, the failing

safety devices must be repaired and activated.

FLASHING LIGHT

Connect the flashing light to J7 flashing light outputs, use flashing lights ACG7059 and bulbs

of 40W maximum.

NB: This electronic K board can only supply power to FLASHING LIGHTS with inbuilt flashing

circuit.

PRE-FLASHING function

The DIP 5 in the ON position enables the pre-flashing, the FLASHING LIGHT and BUZZER

starts working 3 seconds before every movement of the gate.

The DIP 5 in the OFF position disables any pre-flashing, the FLASHING LIGHT, the BUZZER

and the motor will start at the same time.

BUZZER (COM.+ BUZZER-)

The current supplied to the Buzzer will be 200 mA at 24Vdc.

During the normal operation of the gate, opening and closing, the buzzer will buzz

intermittently. Only during the alarm situations (safety strip) the buzzing will almost be

constant.

GATE OPEN INDICATOR (A negativo - LSC)

It is turned ON when the gate is open or partially open, it is turned OFF only when the gate

is completely closed.

N.B.: connect in series to the indicator a resistance of 2K2.

WE RECOMMEND NOT TO OVERLOAD THE INDICATORS OUTPUT OTHERWISE THE GATE

FUNCTIONING COULD BE COMPROMISED OR THE CONTROL BOARD COULD BE DAMAGED.