Default I/O Connections - ABB ACS580-01 Serie Guía Rápida De Instalación

22 EN – R6...R9 Quick installation guide

Default I/O connections

Default I/O connections of the ABB Standard macro are shown below.
R0-
R4
1...10 kohm
R6-
R9
R6-
R9
max.
500 ohm
EN
DA
DE
ES
FI
FR
IT
NL
PL
PT
RU
SV
TR
1)
All control boards do not have switches S1, S2 and S3. In that case, select voltage or current
ZH
for inputs AI1
Total load capacity of the Auxiliary voltage output +24V (X2:10) is 6.0 W (250 mA / 24 V DC).
Wire sizes: 0.14...2.5 mm
Tightening torques: 0.5...0.6 N·m (0.4 lbf·ft)
S1
1)
S2
X1 Reference voltage and analog inputs and outputs
1
2
3
4
5
6
7
8
9
1) S3
X2 & X3 Aux. voltage output and programmable digital inputs
10
11
12
13
14
15
16
17
18
X6, X7, X8 Relay outputs
19
20
21
22
23
24
25
26
27
X5 EIA-485 Modbus RTU
29
30
31
S4
S5
X4 Safe torque off
34
35
36
37
38
X10 24 V AC/DC
40 24 V AC/DC+ in Ext. 24V AC/DC input to power up the control unit
41 24 V AC/DC- in
AI2 and output AO1 with parameters. See the firmware manual.
and
2
(26...16 AWG): All terminals
AI1 U/I Voltage/Current selection for AI1:
AI2 U/I Voltage/Current selection for AI2:
SCR Signal cable shield (screen)
AI1 Output frequency/speed reference: 0...10 V
AGND Analog input circuit common
+10V Reference voltage 10 V DC
AI2 Not configured
AGND Analog input circuit common
AO1 Output frequency: 0...20 mA
AO2 Output current: 0...20 mA
AGND Analog output circuit common
AO1 I/U Voltage/Current selection for AO1:
+24V Aux. voltage output +24 V DC, max. 250 mA
DGND Aux. voltage output common
DCOM Digital input common for all
DI1 Stop (0) / Start (1)
DI2 Forward (0) / Reverse (1)
DI3 Constant frequency/speed selection
DI4 Constant frequency/speed selection
DI5 Ramp set 1 (0) / Ramp set 2 (1)
DI6 Not configured
RO1C
Ready run
250 V AC / 30 V DC
RO1A
2 A
RO1B
RO2C
Running
RO2A 250 V AC / 30 V DC
2 A
RO2B
RO3C Fault (-1)
250 V AC / 30 V DC
RO3A
2 A
RO3B
B+
Embedded Modbus RTU (EIA-485)
A-
DGND
TERM Serial data link termination switch
BIAS Serial data link bias resistors switch
OUT1
Safe torque off. Factory connection. Both circuits
OUT2 must be closed for the drive to start. See chapter
The Safe torque off function in ACS580-01 (0.75
SGND
to 250 kW) hardware manual (3AXD50000018826
IN1
[English]).
IN2
when the main supply is disconnected.
U I
U
I
I U