Tabla De Contenido; Safety Information - Home Decorators Collection 51846 Guía De Uso Y Mantenimiento

Table of Contents
Table of Contents ................................................................ 2
Safety Information ............................................................... 2
Warranty ............................................................................... 3
Pre-Installation .................................................................... 3
Installation ............................................................................ 6

Safety Information

READ AND SAVE THESE INSTRUCTIONS.
1. To reduce the risk of electric shock, ensure the electricity has been
turned off at the circuit breaker or fuse box before you begin.
2. All wiring must be in accordance with the National Electrical Code ANSI/
NFPA 70 and local electrical codes. Electrical installation should be
performed by a qualified licensed electrician.
The outlet box and support structure must be securely mounted and
3.
capable of reliably supporting 35 lbs. (15.9 kg). Use only UL Listed outlet
boxes marked "Acceptable for Fan Support of 35 lbs. (15.9 kg) or less".
4. The fan must be mounted with a minimum of 7 ft (2.1 m) clearance from
the trailing edge of the blades to the floor.
5. Do not operate the reversing switch while the fan blades are in motion.
You must turn the fan off and stop the blades before you reverse the
blade direction.
Do not place objects in the path of the blades.
6.
7. To avoid personal injury or damage to the fan and other items, use
caution when working around or cleaning the fan.
8. Electrical diagrams are for reference only. Light kits that are not packed
with the fan must be UL-listed and marked suitable for use with the
model fan you are installing. Switches must be UL General Use Switches.
Refer to the instructions packaged with the light kits and switches for
proper assembly.
After making electrical connections, spliced conductors should be turned
9.
upward and pushed carefully up into the outlet box. The wires should be
spread apart with the grounded conductor and the equipment-grounding
conductor on one side of the outlet box.
10. All setscrews must be checked and retightened where necessary
before installation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Assembly .............................................................................. 7
Operation ........................................................................... 14
Care and Cleaning ............................................................. 16
Troubleshooting ................................................................. 16
WARNING: To reduce the risk of personal injury,
do not bend the blade brackets (also referred to as
flanges) during assembly or after installation. Do
not insert objects in the path of the blades.
WARNING: To avoid possible electrical shock,
turn the electricity off at the main fuse box before
wiring. If you feel you do not have enough electrical
wiring knowledge or experience, contact a licensed
electrician.
WARNING: Electrical diagrams are for reference
only. Optional use of any light kit shall be UL-listed
and marked suitable for use with this fan.
CAUTION: To reduce the risk of personal injury,
use only the screws provided with the outlet box.
CAUTION: Changes or modifications not expressly
approved by the party responsible for compliance
could void the user's authority to operate the
equipment.
CAUTION: Do NOT use this fan with a dimmer
switch or wall control. Using a dimmer switch or
wall control will damage the fan.
2