Publicidad
Idiomas disponibles
Idiomas disponibles
1A Landing skid
1B Propeller
1C Protective rings
2 REMOTE CONTROL
2A No function
2G Power-LED
2B Control for thrust
2H Trim control for
and rotation
forwards/backwards
2C Button for flight speed
2I Button for Headless
(40%, 70%, 100%)
Mode
2D No function
2J Control for
forwards/backwards
2E Handle
and sideways
2F Antenna
3 INSERTING BATTERIES
3A Unscrew and remove
3B Insert 4 x 1.5 V AA bat-
the cover.
teries and pay atten-
tion to the polarity, as
shown in the battery
compartment.
4 CHARGING THE MODEL
Attention: The battery and motor must cool down for 10 to 15 minutes before
charging and after every flight. Otherwise they can be damaged. The charging process
must be constantly monitored. Always ensure that the charging process takes place on
a fireproof surface in a fire-resistant environment.
1. Push the camera back and fold it down to open the battery compartment (4A).
Unplug the battery from the model and switch off the remote control. Remove the
battery from the model (do not hold on the cable).
2. Plug the battery into the charging socket of the charger, ensuring correct polarity. The
battery must be gently inserted into the charging socket – DO NOT USE FORCE. If the
battery is not correctly inserted into the charging socket, the battery may become
damaged and, under certain circumstances, cause injury.
3. Insert the USB charger in a free USB port (4B).
4. The charging process is complete when the USB charger lights up.
5. Disconnect the battery from the USB charger and disconnect the USB charger from the
USB port once charging is complete.
After a charge time of approx. 60 minutes the model can fly for approx.
5 minutes.
Warning notice: The battery does not normally heat up while charging. If it should
become warm or even hot and/or changes to the surface begin to appear, immediately
discontinue the charging process!
16
1 MODEL
1D Camera and WLAN transmitter
1E Antenna
1F Battery compartment cover
2K Trim control for
sideways
2L ON/OFF switch
2M Battery compartment
cover
3C Close the battery cover
and secure with the
screw.
5 START PREPARATION
Always observe the sequence when switching on! When switching off, always switch
off the model before the remote control.
The model can be controlled with either the supplied remote control or via the
touchscreen/tilt sensors on a smartphone. Photos and videos are also shown and
saved on the smartphone. Install the free app to operate the model:
Switch on the model:
1. Push the camera back and fold it down to open the battery
compartment (see 4A).
2. Push the battery into the battery compartment. Insert the battery
cable in the connection socket on the model (5A). The LEDs on the
model start to flash.
3. After approx. 30 seconds, the model has activated a WLAN hotspot
(XSPYxxxxxxxx). Connect your smartphone to it.
Important! When switching on your model, always place it on an
even horizontal surface – the control electronics aligns its neutral
position to the subsurface.
Controlling with the remote control:
1. The control for thrust and rotation (2B) must point down (5B)
before switching on. Set the ON/OFF switch on the remote control (2L)
to the „ON" position. The power LED (2G) on the remote control flashes.
2. Move the control for thrust and rotation (2B) completely up once and
then completely down again to unlock the remote control. The model is
now ready to start.
3. Start the app on your smartphone to begin the image transmission.
Controlling with a smartphone:
1. Start the app on your smartphone.
Important: Do NOT switch on the remote control.
2. Once the LEDs are continuously lit, the model is ready.
Fold out the antenna
For better reception, please take the antenna on the model out of the mount and it
turn it vertically downwards (5C).
Mounting the smartphone holder
1. Fold up the antenna on the remote control (5D)
2. Mount the smartphone holder on the joint of the antenna (5E)
3. Mount the rear part and screw in place (5F)
4. Push in the smartphone (5G)
Switch off the model: Disconnect the battery cable from the connection socket on the
model.
17
Publicidad
