Specification Chart; Power Ratings - Briggs & Stratton 100000 Manual Del Operador

Problem
The auger does not stop within 5 seconds after
auger control lever is released.
The discharge chute or deflector does not work
(remote-manual).
The snowthrower does not stop when the traction
control is released.
The scraper bar does not clean hard surfaces.
The unit does not propel itself.
The unit does not discharge snow.
For all other issues, contact an authorized service dealer.

Specification Chart

The spark ignition system on this snowthrower complies with Canadian standard ICES-002.
Item Model 100000 Model 120000 Model 130000 Model 150000 Model 19J000 Model 250000
Armature air gap .010 - .014 inch
(,25 - ,36 mm)
Intake Valve .004 - .006 inch
Clearance (,10 - ,15 mm)
Exhaust Valve .006 - .008 inch
Clearance (,15 - ,20 mm)
Oil Capacity 18 - 20 oz
(,54 - ,59 L)
Sparkplug gap .030 inch
(,76 mm)
Engine power will decrease 3.5% for every 1,000 feet (300 meters) above sea level and 1% for every 10 degrees F (5.6 degrees C) above 77 Degrees F
(25 Degrees C). The engine will operate satisfactorily at an angle up to 15 degrees.

Power Ratings

The gross power rating for individual gasoline engine models is labeled in accordance with SAE (Society of Automotive
Engineers) code J1940 Small Engine Power & Torque Rating Procedure, and is rated in accordance with SAE J1995. Torque
values are derived at 2600 RPM for those engines with "rpm" called out on the label and 3060 RPM for all others; horsepower
values are derived at 3600 RPM. The gross power curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power
values are taken with exhaust and air cleaner installed whereas gross power values are collected without these attachments.
Actual gross engine power will be higher than net engine power and is affected by, among other things, ambient operating
conditions and engine-to-engine variability. Given the wide array of products on which engines are placed, the gasoline engine
may not develop the rated gross power when used in a given piece of power equipment. This difference is due to a variety
of factors including, but not limited to, the variety of engine components (air cleaner, exhaust, charging, cooling, carburetor,
20
Look for
The auger control cable is not adjusted correctly.
The discharge chute or deflector in not adjusted
correctly.
The discharge chute or deflector needs lubrication. Lubricate the control linkage and pivot points.
The traction control cable is not adjusted correctly. See Adjusting the Traction Control Cable.
The kid shoes are not correctly adjusted.
Worn scraper bar.
Incorrect adjustment of traction control cable.
The auger control cable out of adjustment.
Broken shear pin or shear bolt.
The discharge chute is clogged.
Unwanted debris is lodged in auger.
.010 - .014 inch .010 - .014 inch
(,25 - ,36 mm) (,25 - ,36 mm)
.004 - .006 inch .004 - .006 inch
(,10 - ,15 mm) (,10 - ,15 mm)
.009 - .011 inch .006 - .008 inch
(,23 - ,28 mm) (,15 - ,20 mm)
18 - 20 oz 18 - 20 oz
(,54 - ,59 L) (,54 - ,59 L)
.030 inch .030 inch
(,76 mm) (,76 mm)
See Adjusting the Auger Cable.
Adjust the control linkage and pivot points.
See Adjusting the Discharge Chute or Adjusting
the Deflector.
See Lubricating the Control Lever Linkage.
Raise or lower the skid shoes. See Adjusting the
Skid Shoe Height.
Replace the scraper bar. See Replacing the
Scraper Bar.
See Adjusting the Traction Control Cable.
Adjust auger control cable. See Adjusting the
Auger Cable.
Replace shear pin or bolt. See Replacing the Shear
Pins or Shear Bolts.
STOP THE ENGINE! Make sure that the auger and
impeller have stopped rotating. Use a clean-out
tool to remove the snow from the discharge chute.
DO NOT clear a clogged discharge chute with your
hands! See Clearing a Clogged Discharge Chute.
STOP THE ENGINE! Make sure that the auger and
impeller DO NOT rotate. Use a clean-out tool to
remove the foreign object. DO NOT clear a lodged
object with your hands! See Clearing a Clogged
Discharge Chute.
Specifications
.010 - .014 inch .008 - .016 inch
(,25 - ,36 mm) (,2 - ,4 mm)
.004 - .006 inch .005 - .007 inch
(,10 - ,15 mm) (,13 - ,18 mm)
.009 - .011 inch .005 - .007 inch
(,23 - ,28 mm) (,13 - ,18 mm)
18 - 20 oz 36 - 38 oz
(,54 - ,59 L) (1,0 - 1,1 L)
.030 inch .030 inch
(,76 mm) (,76 mm)
Remedy
.008 - .016 inch
(,2 - ,4 mm)
.005 - .007 inch
(,13 - ,18 mm)
.005 - .007 inch
(,13 - ,18 mm)
36 - 38 oz
(1,0 - 1,1 L)
.030 inch
(,76 mm)