Introduction And Assembly; Ultimatesam Humidifi Cation System (Sa*); Distributor Dimensions And Weights - Carel ultimateSAM Manual Del Usuario

1.1 ultimateSAM Humidifi cation System (SA*)
Each UltimateSAM Humidifi cation System consists of the following:
•
a humidifi er steam distributor
•
steam trap(s) and strainer(s) (sold separately)
•
a controlling humidistat and/or sensor (sold separately)
•
a steam control valve & actuator for use with pressurized steam sources
(sold separately)
•
other optional equipment that may be required.

1.2 Distributor dimensions and weights

" Y "
The system for identifying the humidifi er steam distributor is shown in Table
1.b. The table also provides the width (Dimension "X") and height (Dimension
"Y"). The front-to-back depth of all distributor is the same, 133mm (5.25").
NOTE: The height dimension assumes that the bottom pedestals are in the
factory-assembled position. (See section 1.4 for details on other pedestal
heights.)
The weights of the various distributor confi gurations, including the frame,
are shown on Table 1.a. The table shows weights for only the smallest and
largest width and height distributors. A complete weight table for all width
and height codes can be found in section 8, "Specifi cations. "
Weight in kg (lb)
SABA*SI300
SABA*LI300
SABA*HI300
SABR*SI300
SABR*LI300 46.0 (101)
SABR*HI300 47.5 (105)
SATA*SI300
SATA*LI300
SATA*H300
SATR*SI300 55.0 (121)
SATR*LI300 56.5 (124)
SATR*H300 58.5 (129)

1. INTRODUCTION AND ASSEMBLY

" X "
Fig. 1.a
Height Code
A Q
7.5 ( 17) 21.0 ( 46)
8.0 ( 18) 22.5 ( 50)
8.5 ( 19) 25.5 ( 56)
44.0 ( 97) 126.0 (277)
139.5 (307)
202.5 (446)
10.0 ( 22) 23.0 ( 51)
10.0 ( 22) 24.5 ( 54)
10.5 ( 23) 28.0 ( 62)
137.0 (301)
150.0 (330)
213.5 (470)
SA
 ID prefi x
 Feed type:
 Width:
 Height:
 Uprights:
 Insulation:
 Frame:
 Drain:
Tab. 1.a
 ---
For additional dimensions regarding features on the distributor, like drain
locations, see section 8, "Specifi cations. " See other sections of this manual for
details on other ultimateSAM items, such as valves and traps.
7
x x x x x x
B= Bottom feed
T=Top feed
Code Dimension 152mm
"X" (6")
mm (in) spacing
A= 447 (17.75) 2
B= 599 (23.75) 3
C= 751 (29.75) 4
D= 903 (35.75) 5
E= 1055 (41.75) 6
F= 1207 (47.75) 7
G= 1359 (53.75) 8
H= 1511 (59.50) 9
I= 1663 (65.50) 10
J= 1815 (71.50) 11
K= 1967 (77.50) 12
L= 2119 (83.50) 13
M= 2271 (89.50) 14
N= 2423 (95.50) 15
O= 2575 (101.50) 16
P= 2727 (107.50) 17
Q= 2879 (113.50) 18
R= 3031 (119.50) 19
Dimension "Y" mm (in)
Code Botom feed Top feed
A= 598 ( 23.75) 749 ( 29.50)
B= 750 ( 29.75) 901 ( 35.50)
C= 902 ( 35.75) 1053 ( 41.50)
D= 1054 ( 41.50) 1205 ( 47.50)
E= 1206 ( 47.50) 1357 ( 53.50)
F= 1358 ( 53.50) 1509 ( 59.50)
G= 1510 ( 59.50) 1661 ( 65.50)
H= 1662 ( 65.50) 1813 ( 71.50)
I= 1814 ( 71.50) 1965 ( 77.50)
J= 1966 ( 77.50) 2117 ( 83.50)
K= 2118 ( 83.50) 2269 ( 89.50)
L= 2270 ( 89.50) 2421 ( 95.50)
M= 2422 ( 95.50) 2573 (101.50)
N= 2574 (101.50) 2725 (107.50)
O= 2726 (107.50) 2877 (113.50)
P= 2878 (113.50) 3029 (119.50)
Q= 3030 (119.50) 3181 (125.25)
OD
Interasse mm
Code mm (in)" (in)
S= 152 (6.00) 35 (1.50)
L= 152 (6.00) 45 (1.75)
H= 76 (3.00) 35 (1.50)
I= insulated uprights w/ nozzles
N= uninsulated uprights w/o nozzles
0= no frame, unassembled
1= no frame, assembled
2= w/ frame, unassembled
3= w/ frame, assemble
U= ¾" Male NPT
0= ¾" Male Gas
---
"Ultimate SAM" +0300013EE - rel. 1.0 - 28.10.2010
ENG
x 0
No. of uprights
76mm
(3")
spacing
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
Tab. 1.b