Components And Materials; Associated Equipment - Tractel HT43 Manual De Instalación, De Utilización Y De Mantenimiento

Ocultar thumbs Ver también para HT43:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 30
• to use this equipment if the safety function of any of
the associated items is affected by the safety function
of another item or may interfere with it.
• To anchor an HT/ET harness or CE work station
support belt through a fall-arrest system to a structural
anchor where the resistance is less than 12 kN, or
perceived as such.
• to perform any repair or maintenance operations on
this equipment without first having been trained and
qualified, in writing, by Tractel
• to use this equipment if it is not complete, if it has been
dismantled beforehand or if components have been
replaced by any person not unauthorised by Tractel
6. Installation
Figure 3, page 5.
Assemble all adjustment loops of the harness when the
operator is wearing it.
Regularly check the adjustment and fixing elements
when using the equipment.
Adjust the lengths of the various straps: they should not
be over or undertightened to obtain maximum comfort
when using the system and for optimum fall-arrest
protection. The harness will ensure efficient protection
under these conditions.
• Whenever possible, the structural anchor point will be
located at a height between 1.5 and 2 metres above
the operator's feet. The structural anchor point must
withhold a minimal resistance of 12 kN.
• The connection to the anchoring point or to the
structure must be done using an EN 362 connector.
• For
the
connection
system
to
the
fall-arrest
the
instructions
of
fall-arrest system in order to use the proper anchorage
point and the proper attaching procedure.
• Connection of the support lanyard to the maintenance
belt:
– Hook the first connector to the lateral point of the
belt Fig 3a.
– Pass the retaining lanyard around the support and
clip the connector to the end of the lanyard on the
2nd side point of the belt.
– Adjust the length of the retaining lanyard (see
instructions for the retaining lanyard).
DANGER
Before and during use, it is necessary to plan out
how possible rescue can be efficiently and safely
conducted, within less than 15 minutes. Beyond
this time, operator is in danger.
.
®
®
of
the
fall-arrest
harness,
refer
to
the
harness
and
the

7. Components and materials

Figure 1, on page 3: Harness - EN 361 - EN 358 - EN
1497.
a.
PES shoulder strap.
b.
PE Backplate.
c.
Elastomer loop.
d.
Steel adjustment buckle.
e.
Steel side clip (fall-arrest point, see Figure 1, on
page 3).
f1. Steel sternal attachment (fall arrest point)
f2. Sternal attachment in PES «A/2» x 2 (fall arrest
.
point)
g.
Steel back clip (fall-arrest point, see Figure 1, on
page 3).
h.
PES buttock strap.
i.
PP chest buckle.
j.
Marking label.
k.
Marking "A", of the attachment points, on the D ring
or the strap.
l.
Steel side clip (handling point, see Figure 1, on
page 3).
m. Backplate in PE foam and fabric.
n.
Marking label.
o.
POM service ring.
p.
Steel adjustment buckle.
q.
Elastomer loop.
r.
Rescue strap.
s.
Rescue lanyard label.
t.
Attachment D-ring for rescue.
• Strap + seam threads: polyester.
• Loops made of galvanized steel and aluminum.
• Cordura-covered foam back piece.
• Back
plate,
loops:
elastomer.

8. Associated equipment

An EN 363 fall arrest system consists of the following
elements:
• An anchorage (EN 795).
• An end connector (EN 362).
• A fall-arrest device (EN 353-1/2-EN35- EN360)
• A connector (EN 362).
• A fall-arrest harness (EN 361).
All other associations are forbidden.
An EN 361 fall arrester harness is the only
body-gripping device authorised for use in a fall
prevention system.
polyethylene,
thermoplastic
DANGER
GB
9

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

En361En358

Tabla de contenido