Circuit Board Parameters - klover PB 35 Instalación, Uso Y Mantenimiento, Consejos Útiles

...black of power (black out)
If power is missing for a time less than Pr48, when restored the boiler immediately re-starts from operative state it had before power outage (recovering the
set work power).
If power is missing for a time greater than Pr48, when restored the boiler is placed at "STOP FIRE" (stand-by) mode and carries out the entire switch off
cycle until it cools down. Once this phase is completed, the boiler can be normally switched on to proceed working at the set power.
Previous state
OFF
START
START
P-LOAD PELLET
FLAME STAND-BY
FIRE PRESENT
FIRE PRESENT
WORK (any phase)
WORK (any phase)
BRAZIER CLEANING
BRAZIER CLEANING
FINAL CLEANING
FINAL CLEANING
STOP FIRE

CIRCUIT BOARD PARAMETERS

THE PARAMETERS MEMORISED ON THE CIRCUIT BOARD ARE FUNDAMENTAL FOR THE CORRECT FUNCTIONING OF THE BOILER.
THE PARAMETERS GIVEN BELOW ARE ALREADY MEMORISED IN THE BOILER INSPECTION PHASE DIRECTLY IN THE FACTORY.
THESE PARAMETERS ARE THE RESULT OF CAREFUL TESTS WITH VARIOUS TYPES OF PELLETS AND MUST NOT BE CHANGED WITHOUT
THE AUTHORISATION OF KLOVER srl, SO AS NOT TO JEOPARDISE BOILER FUNCTIONING.
ALL RESPONSIBILITIES ARE DECLINED FOR DAMAGE CAUSED BY INCORRECT INTRODUCTION OF THE PARAMETERS.
Parameter Menu level
Pr38 M – 9 – 4 – 01 Re-ignition block
Pr39 M – 9 – 4 – 02 Flue gas intake device switch-off time
Pr40 M – 9 – 4 – 03 Pre-load time in ignition
Pr41 M – 9 – 4 – 04 Stand-by time after pre-load
Pr42 M – 9 – 4 – 05 Intake device speed in pre-load phase
ON/OFF Temperature hysteresis on "SET
Pr43 M – 9 – 4 – 06
H2O" and "SET DHW"
Delay to economy switch-off (timer after
Pr44 M – 9 – 4 – 07
reaching "SET H2O")
Pr45 M – 9 – 4 – 08 Power change delay
ON/OFF Temperature hysteresis on "SET
Pr46 M – 9 – 4 – 09
ROOM"
Pr47 M – 9 – 4 – 10 Keypad block enabling
Pr48 M – 9 – 4 – 11 Automatic re-ignition after black-out
Pr49 M – 9 – 4 – 12 Pellet level sensor enabling
Pr50 M – 9 – 4 – 13 Pump ignition for over-temperature safety
Black-out duration State after power restore
Any OFF
duration < Pr48 START
duration > Pr48 START
Any BLACK OUT ALARM
Any BLACK OUT ALARM
duration < Pr48 FIRE PRESENT
duration > Pr48 STOP FIRE with automatic re-ignition after machine cooling
duration < Pr48 WORK (any phase)
duration > Pr48 STOP FIRE with automatic re-ignition after machine cooling
duration < Pr48 BRAZIER CLEANING
duration > Pr48 STOP FIRE with automatic re-ignition after machine cooling
FINAL CLEANING and after cooling  OFF
duration < Pr48
FINAL CLEANING and after cooling  OFF
duration > Pr48
Any STOP FIRE
"Various calibrations" (Menu M – 9 – 4)
Description Display writing Measurement
RE-IGNIT BLOCK Minutes
MIN-INT OFF Minutes
IGNIT- PRE-LOAD Seconds
AFTER-PRE STAND-BY Seconds
PRELOAD FLUE GAS-
Revs/min
INTAKE DEVICE
DELTA ON OFF AUTO
DELAY-OFF AUTO Minutes
POWER CHANGE Seconds
DELTA ON AUTO
KEYS BLOCK-EN On – off
BLACK OUT RE-IGNITION Seconds
PELLET RESERVE On – off
PUMP SAFETY
21
Value field
0 – 10
0 – 20
0 – 225
0 – 255
350 – 2800
°C 0 – 20
2 – 120
0 – 60
°C 0 – 15
On – off
0 – 60
On – off
°C 60 - 90
Database
6
10
90
170
2100
5
30
20
2
Off
30
On
83