Technical Data - Stanley FATMAX SFMCS500 Manual De Instrucciones

ENGLISH
Hints for optimum use
● Always use the appropriate type of saw blade for the
workpiece material and type of cut.
● Always hold the tool with both hands.
● Let the blade run freely for a few seconds before starting
the cut.
● Apply only a gentle pressure to the tool while performing
the cut.
● Work with the shoe pressed against the workpiece.
● As some splintering along the line of cut on the top side of
the workpiece cannot be avoided, cut on the side where
splintering is acceptable.
● Where splintering is to be minimised, e.g. when cutting
laminates, clamp a piece of plywood onto the top of
the workpiece.
● Support large panels to minimize the risk of blade pinching
and kickback. Large panels tend to sag under their
own weight.
● Supports must be placed under the panel on both sides,
near the line of cut and near the edge of the panel
being cut.
● Never hold piece being cut in your hands or across
your leg.
● Secure the workpiece to a stable platform using clamps. It
is important to support the work properly to minimize body
exposure, blade binding, or loss of control.
Accessories
The performance of your tool depends on the accessory
used. STANLEY FATMAX accessories are engineered to high
quality standards and designed to enhance the performance
of your tool. By using these accessories you will get the very
best from your tool.
Maintenance
Your STANLEY FATMAX tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
@
regular cleaning.
Warning! Before performing any maintenance on
the tool, remove the battery from the tool. Unplug the
charger before cleaning it.
● Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
● Regularly clean the motor housing using a damp cloth.
● Do not use any abrasive or solvent-based cleaner.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
● Safely dispose of the old plug.
10
(Original instructions)
● Connect the brown lead to the live terminal in the
new plug.
@
● Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the
@
earth terminal.
Follow the fitting instructions supplied with good
quality plugs.
Recommended fuse: 5 A.
Protecting the environment
Z
Separate collection. Products and batteries marked
with this symbol must not be disposed of with
normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com

Technical data

Voltage
No-load speed
Max. depth of cut
Max depth of cut at 45º bevel
Blade diameter
Blade bore
Blade tip width
Weight
Charger SFMCB11
Input Voltage V
AC
Output Voltage V
DC
Current A
Battery SFMCB201
Voltage 18
V
DC
Capacity Ah 1.5
Type
Li-Ion
Level of sound pressure according to EN62841:
Sound pressure (L ) 86 dB(A), uncertainty (K) 3 dB(A)
pA
Sound power (L ) 97 dB(A), uncertainty (K) 3 dB(A)
WA
Vibration total values (triax vector sum) according to EN62841:
2
Cutting wood (a ) 1.6 m/s , uncertainty (K) 1.5 m/s
h, w
SFMCS500
V
DC
Min 0 - 4,000
-1
mm
mm
mm
mm
mm
kg
SFMCB12 SFMCB14
230 230
18 18
1.25 2
SFMCB202 SFMCB204 SFMCB206
18 18
2.0 4.0
Li-Ion Li-Ion
2
18V
54
45
165
16
2.0
3.4
230
18
4
18
6.0
Li-Ion