Setting The Test Tone - Denon AVR-1306 Instrucciones De Operación

System Setup

Setting the Test Tone

• Use this setting to adjust to that the playback level between the
different channel is equal.
• From the listening position, listen to the test tones produced
from the speakers to adjust the level.
• The level can also be adjusted directly from the remote control
unit.
1
CURSOR F F
Press the button to switch the test
•
tone mode.
CURSOR H H
ENTER
Press the or
•
switch to the digital input (COAXIAL) setting.
* T E S T T O N E Y e s <
2 CURSOR F F G G
Press the or button to select the
test tone mode, then press the
button to start test tone.
T . T O N E A u t o >
Auto Manual
Auto:
Adjust the level while listening to the test tones produced
automatically from the different speakers.
Manual:
Select the speaker from which you want to produce the test
tone to adjust the level.
3 CURSOR F F G G
Press the or
front L channel level, then press the
button to switch to the center channel level
(manual mode).
A U T O - F L
F L V O L
-12dB
4
Press the
center channel level, then press the
button to switch to the front R channel level
(manual mode).
5
Press the
front R channel level, then press the
button to switch to the surround R channel level
(manual mode).
button to
6
Press the
surround R channel level, then press the
CURSOR H H
channel level (manual mode).
7
Press the
CURSOR H H
surround L channel level, then press the
CURSOR H H
channel level (manual mode).
8
Press the
subwoofer channel level, then press the
button to finish the test tone.
9
Press the
the Digital In Assignment (COAXIAL) setting.
• When adjusting the level of an active subwoofer system, you
may also need to adjust the subwoofer's own volume control.
button to set the
• When you adjust the channel levels while in the system setup
CURSOR H H
channel level mode, the channel level adjustments made will
affect all surround modes. Consider this mode a master
channel level adjustment mode.
• After you have completed the system setup channel level
adjustments, you can then activate the individual surround
modes and adjust channel levels that will be remembered for
each of those modes. Then, whenever you activate a particular
surround sound mode, your preferred channel level
0 d B
adjustments for just that mode will be recalled. Check the
instructions for adjusting channel levels within each surround
0dB +12dB
mode ( page 27).
CURSOR F F G G
or button to set the
CURSOR H H
CURSOR F F G G
or button to set the
CURSOR H H
CURSOR F F G G
or button to set the
button to switch to the surround L
CURSOR F F G G
or button to set the
button to switch to the subwoofer
CURSOR F F G G
or button to set the
ENTER
CURSOR H H
ENTER
or button to switch
14
ENGLISH
2 Adjusting the test tone
• Before playing with the surround function, be sure to use the
test tones to adjust the playback level from the different
speakers. This adjustment can be performed with the system
setup or from the remote control unit, as described below.
• Adjusting with the remote control unit using the test tones is
only possible in the "Auto" mode and only effective in the
STANDARD (DOLBY/DTS SURROUND) modes. The adjusted
levels for the different modes are automatically stored in the
memory.
1
STANDARD
Press the button to select the
STANDARD (DOLBY/DTS
modes.
2
TEST TONE
Press the button.
• Test tones are output from the different speakers.
3
CURSOR F F G G
Press the or button to adjust so
that the volume of the test tones is the same for
all the speakers.
4 After completing the adjustment, press the
TEST TONE
button again.
ENGLISH
System Setup
SURROUND)