Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
O
E
PTIONAL
QUIPMENT
Digital Audio Out Connection
Use the diagram below to connect the Digital Audio Output of your
HDTV Projection Television to a Dolby Digital decoder.
Digital Audio Out
Dolby Digital 5.1 channel surround sound delivers digital-quality
sound. Dolby Digital provides five discrete full-bandwidth
channels for front left, front right, center, surround left and
surround right, plus a LFE (Low Frequency Effect) subwoofer
channel. For a full Home Theater sound experience, an external
Dolby Digital decoder and a multichannel amplifier must be
connected to the Digital Audio Out jack on the PTV.
ANT A
Cable In
ANT B
TERMINALS ON BACK OF PROJECTION TELEVISION
VIDEO
Y
DCM
HDMI
INTERFACE
P
B
SERVICE
A/V IN
ONLY
P
R
L
R
1
2
L
AUDIO
COMPONENT
INPUT
INPUT
VIDEO INPUT
1
AUDIO IN
R
DIGITAL AUDIO OUT
CABLES NOT SUPPLIED
Procedure
•
Connect the Digital Audio cable from the Digital Audio
Out jack on the PTV to the Digital Audio In connection on
the Dolby Digital decoder.
Note:
When ATSC channel is selected, the output from the
Digital Audio Out jack will be Dolby Digital. But, if NTSC
channel is selected, the output will be PCM.
Program Out Connection (PROG OUT)
You can connect a VCR to the PROG OUT terminal to
record the program you are viewing on-screen. An external
monitor can also be connected to the PROG OUT and TO
AUDIO AMP terminals. Connect the VCR as shown below.
ANT A
Digital In
ANT B
TERMINALS ON BACK OF PROJECTION TELEVISION
VIDEO
DCM
Y
HDMI
INTERFACE
P
B
SERVICE
A/V IN
ONLY
P
R
L
R
1
2
L
AUDIO
COMPONENT
INPUT
INPUT
VIDEO INPUT
1
AUDIO IN
CABLES NOT SUPPLIED
R
DIGITAL AUDIO OUT
Procedure
•
Connect the VCR to PROG OUT and TO AUDIO AMP
terminals
•
PROG OUT terminal display is the same as on-screen
display.
•
See the VCR instruction manual for further instructions
for recording the program.
Notes:
•
This TV contains Video and Audio Outputs for the
purpose of recording television programming to VCR.
Due to license restrictions, if a device (STB, DVD, etc.) is
8
C
ONNECTIONS
S-VIDEO
Six channel Speaker system
VIDEO
L
R
INPUT
PROG
TO AUDIO
2
3
OUT
AMP
VCR
S-VIDEO
VIDEO L - AUDIO - R
VIDEO
L
R
INPUT
PROG
TO AUDIO
2
3
OUT
AMP
connected to the HDMI input of the TV, no video or audio
output is allowed.
•
Program Out signal may not be available when
component input is selected for main picture.
•
Program Out signal is available when receiving digital
channel. However, all digital formats are down converted
to composite NTSC video.
•
When receiving digital or analog channels signals and
the analog or digital CC is ON, Program Out connector
will output open caption text in the NTSC video picture. If
CC is OFF, only analog CC closed caption code is
passed out the Program Out connector.
•
Certain program content output from the Program Out
connector may have the Macrovision signal modification
applied to its signal, preventing VCRs from recording this
video signal.
Amplifier Connection (Analog)
Amplifier
To listen the audio through a separate stereo system,
90.7 MHZ
connect an external audio amplifier TO AUDIO AMP
OPTICAL IN
outputs on back of television.
Note:
TO AUDIO AMP terminals cannot be connected directly
to external speakers.
ANT A
Cable In
ANT B
TERMINALS ON BACK OF PROJECTION TELEVISION
DCM
HDMI
INTERFACE
SERVICE
A/V IN
ONLY
L
AUDIO
AUDIO IN
R
DIGITAL AUDIO OUT
Audio Adjustments
•
Select Speakers Off in Audio Other Adjust menu.
•
Set amplifier volume to the preferred level.
PLAY
R
E
FF
W
STOP
ANT OUT
OUT
IN
ANT IN
VIDEO
Y
P
B
S-VIDEO
P
VIDEO
R
L
L
R
R
2
1
COMPONENT
INPUT
INPUT
INPUT
PROG
TO AUDIO
CABLES NOT SUPPLIED
VIDEO INPUT
1
2
3
OUT
AMP
90.7 MHZ
Publicidad
Capítulos
Tabla de contenido
