Incorrect Use Of The Machine; Instructions For Maintenance, Adjustment And Safety Of People - Primus I35/50 Manual De Uso

The machine is not designed for the ironing of linen which contains parts made out of metal, plastic, glass
fibres or rubber foam.
Only linen with a residual moisture of 40±10% can be inserted into the Ironer. The Ironer will perform the
final drying. It is necessary to spin or pre dry linen with a higher residual moisture. Before Ironing, sprinkle
with water linen that is too dry otherwise over dried linen can stick on ironing belts and ironing rollers at
machines with front/rear delivery with folder.
The linen must be properly rinsed. Not following this instruction may lead to yellowing of linen and deposits
of washing agents and dirt.
The linen must be sorted according to its type and wash temperature. It is necessary to empty out the pockets, and
remove foreign objects like nails, pins, screws and so on, to avoid damage to the linen and the machine.
Clean the dust filter daily:
– Remove the cover(s) of dust filter(s) of the (cold) machine and take off the filter. Check the filter condition and remove
dust from it. Put the cleaned filter back and close the cover.
Place the linen on the feed belt alternatively between right and left, or gradually from left to right, so that the
roller is evenly loaded during heat transfer.
Warning for ironer with front/rear delivery with folder: only that linen will be folded, which goes through
the middle of ironing roller.
Place laundry with buttons face up (buttons up) so that the buttons can get pressed into the roller cover.
Be careful when ironing synthetic materials, so that they do not get stuck to the roller.
Never leave the linen in the machine.
Minimal fluctuations in the temperature can be influenced by a well skilled operator, who, depending on the
type of ironed linen and its residual humidity, changes the set temperature and the ironing speed on the
control unit. To get the maximum output from the Ironer, it is recommended to:
– avoid temperature decrease by correct ironing procedure
– try to iron fluently and smoothly.
– lower the amount of time when there is no ironing being done when the temperature is at the working level.
– group together linen according to the material, fibre type or residual moisture.
– adjust the ironing speed and temperature to the specific needs of each ironing.

2.3. INCORRECT USE OF THE MACHINE

WARNING !
!
THIS MACHINE WAS DESIGNED FOR INDUSTRIAL IRONING AND DRYING OR ALSO FOLDING OF LINEN
WASHED IN WATER.
ANY OTHER USE WITH OUT THE MANUFACTURER'S WRITTEN CONSENT WILL BE UNDERSTOOD AS
INCORRECT USE OF THE MACHINE.
– Do not use the reverse action for any other purpose than to free a person or a caught object.
– Do not iron linen whose structure prevents the retention of moisture.
– Do not iron with out alternatively placing the linen on the right and left side.
– Do not turn off the power supply to the machine if the machine's temperature is higher than 80°C, except in exceptional
situations.
– When ironing small pieces, do not leave a lot of space between the pieces along the entire length of the roller.
– Do not run the machine at top speed during heating and cooling of the machine.
– Do not stop the machine if the ironing belts are not completely dry. Do not iron below 80 degrees C, to avoid oxidation
of the roller.
– Do not insert into the ironer linen which contain objects whose hardness can damage the roller surface or the belts.
– Do not iron synthetic fibres at high temperatures.

2.4. INSTRUCTIONS FOR MAINTENANCE, ADJUSTMENT AND SAFETY OF PEOPLE

Some important information for the usage of the machine are not (or only partly) mentioned in this User´s Manual.
You can find missing information in Installation and Maintenance manual, which is delivered with the machine.
References to „Installation and Maintenance manual" according to norm EN ISO 10472-1(-5):
1. Information about providing User´s manual
2. Range of machine use and limitation
3. Maintenance and adjustment
4. Description of qualities for ventilation
5. Covers
6. Defects, cleaning and maintenance
7. Heat risks
8. Exhaust
9. Handling, Installation
10. Change of pad of pressure roller
11. Places of grip
8 USER´S MANUAL PUBLICATION DATE 10/03 508 816