Loading The Tool - Bostitch 438 Traducción Del Original

SAFETY INSTRUCTIONS
© Stanley Bostitch
IMPORTANT READ CAREFULLY: It is important that all operators read and understand all sections
of this Tool Technical Data manual and the separate Safety and Operating Instruction Manual which
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
come with this tool. Failure to do so could result in you or others in the working area to be seriously injured.
compliance for the products.
WARNING! Eye protection in accordance with 89/686/EEC, and with equal or greater grade than defined in
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
EN166 should be used. However all aspects of operators work, environment and other type/s of machinery
rien que les produits soient conformes aux normes CE.
being used, should also be considered when selecting any personal protection equipment. Note: Non-side
shielded spectacles and face shields alone do not provide adequate protection.
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
die CE-Richtlinien für Produkte.
WARNING! To prevent accidental injuries:
●
Never place a hand or any other part of the body in fastener discharge area of tool.
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
●
Never point tool at yourself or anyone whether it contains fasteners or not.
zeggen dat de producten voldoen aan de CE-vereisten.
●
Never engage in horseplay.
●
Never pull the trigger unless the nose is directed towards the work.
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
●
Always handle the tool with care.
produkterne.
●
This tool is intended to be used for fastening wood to wood in pallet/crate and construction applications.
DO NOT USE for fastening harder materials which could cause buckling of the fasteners and damage to the
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
tool. If you are unsure of the suitability of this tool for certain applications, please contact your local sales
yhdenmukaisuutta.
office.
●
Do not pull the trigger or depress the trip mechanism whilst loading the tool.
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα αντίγραφα του παρόντος
●
To prevent accidental actuation and possible injury, always disconnect air supply.
εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
1. Before making adjustments. 2. When servicing the tool. 3. When clearing a jam. 4. When tool is not in use.
5. When moving to a different work area, as accidental actuation may occur, possibly causing injury.
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
●
Read the additional Safety & Operating instructions booklet before using tool.
conformità CE per i relativi prodotti.
●
Do not use oxygen and combustible gases as an energy source for pneumatically operated tools.
●
The operation of this tool can cause sparks and act as a source of ignition for flammable fuels and gases.
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for CE-
merking for produktet.

LOADING THE TOOL

1. Move the pusher to rear until latched. Cover will open. Pusher front will drop into notch on top of magazine
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
rail. (Fig 1)
conformidade com a CE para os produtos.
2. Drop staple stick over magzine and slide forward. Repeat until magazine is loaded, allowing enough space
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
for pusher to disengage the magazine and the cover to close (approximately 13mm.) (Fig 2)
conformidad con las normas CE de los productos.
3. Pull and hold top part of knob and depress bottom part of knob in a clockwise direction to release pusher.
(Fig 3)
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
Note: Use only fasteners recommended by Bostitch for use in Bostitch tools or nails which meet Bostitch
specifications.
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
stanowią deklaracji zgodności CE prezentowanych produktów.
TM
"DIAL-A-DEPTH " FASTENER CONTROL ADJUSTMENT (Fig 4,5,6)
The DIAL-A-DEPTH TM Fastener Control adjustment feature provides close control of the fastener drive depth;
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
stanowią deklaracji zgodności CE prezentowanych produktów. from flush with the work surface to shallow or deep countersink. First, set the air pressure for consistent drive in
the specific work, then use the DIAL-A-DEPTH
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
TO ADJUST DIAL-A-DEPTH
výrobky.
1. With air pressure set, drive a few fasteners into a representative sample of the material to determine if
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem jelenti
adjustment is necessary.
a termék CE-megfelelőségét.
2. If adjustment is required, disconnect air supply.
3. Remove cover mounting nuts and cover. Tilt out the contact trip arm assembly. Rotate the adjusting nut to the
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
left to increase fastener drive depth, or to the right to decrease it. Reinstall the contact arm assembly, cover and
conformitatea CE pentru produse.
mounting nuts.
TM
Fastener Control adjustment to give the desired depth of drive.
TM
FASTENER CONTROL ADJUSTMENT:
GB