DENTSPLY digit power Guia De Funcionamiento página 3

6. WARRANTY
• Except with respect to those components parts and uses which are hereinafter described, DENTSPLY warrants this digit power
for a period of two (2) years from the date of sale. DENTSPLY's liability under this warranty is limited solely to repairing or, at DENTSPLY's option, replacing those products included within the
warranty which are returned to DENTSPLY within the applicable warranty period (with shipping charges prepaid), and which are determined by DENTSPLY to be defective. This warranty shall not
apply to any product which has been subject to misuse; negligence; or accident; or misapplied; or modified; or repaired by unauthorized persons; or improperly installed.
• INSPECTION: Buyer shall inspect the product upon receipt. The buyer shall notify DENTSPLY in writing of any claims of defects in material and workmanship within thirty (30) days after the buyer
discovers or should have discovered the facts upon which such a claim is based. Failure of the buyer to give written notice of such a claim within this time period shall be deemed to be a waiver
of such claim.
• DISCLAIMER: The provisions here-in stated DENTSPLY sole obligation and exclude all other remedies or warranties, expressed or implied, including those related to MERCHANTABILITY and
FITNESS FOR A PARTICULAR PURPOSE.
• LIMITATION OF LIABILITY: Under no circumstances shall DENTSPLY be liable to the buyer for any incidental, consequential or special damages, losses or expenses.
• LIMITATION OF ACTIONS: The buyer must initiate any action with respect to claims under the warranty described in the first paragraph within one (1) year after the cause of action has accrued.
AIR SUPPLY HOSE REPLACEMENT
• Step 1: Remove the old air supply hose from the digit power
pulling off the hose. Technique tip: Use your thumb and index finger to hold the push fitting down tightly while pulling the
hose in the other direction.
• Step 2: The new air hose can be cut to length with scissors if desired.
• Step 3: Insert the new air hose into the push fittings. Technique tip: When pushing the air hose into the push fitting, it will
push in easily and then encounter a small resistance – continue pushing in firmly past this initial resistance.
• Step 4: Confirm that the air hose is properly connected to the push fitting by pulling gently on the hose.
• Step 5: Test the unit for proper assembly without a digit power
push in firmly.
ADAPTER REPLACEMENT
Traditional Style Delivery Unit
• Step 1: Test fit the Adapter post in the tool holder. If necessary, adjust the arm length on the Adapter by removing the screw and selecting
the proper alignment hole for a customized fit.
• Step 2: Attach the Regulator to the Adapter using the threaded nut as shown. The Regulator knob should face up. Put the Dispenser in the
Adapter cradle with the dispensing end up.
• Step 3: Attach the Regulator to the dental hose via an ISO threaded connector or quick connect coupler depending on your configuration.
• Step 4: Place the Regulator in the tool holder to deactivate the air line.
• Step 5: Place the Adapter post in the tool holder to activate the air line. Dispense material using the foot control.
Step 1
Continental Style Delivery Unit
• Step 1: Remove the sliding arm by removing the screw.
• Step 2: Attach the Regulator to the Adapter using the threaded nut as shown. The Regulator knob should face down. Put the Dispenser in the
Adapter cradle with the dispensing end up.
• Step 3: Attach the Regulator to the dental hose via an ISO threaded connector or quick connect coupler depending on your configuration and place on the tool rest.
• Step 4: To activate the air line, pull the assembly off of the tool rest and set it on the procedure tray. Dispense material using the foot control.
Step 1
™ Dispenser by holding down the push fitting while simultaneously
™ cartridge. If the air hose leaks or pops off, reattach it and
Step 2 Step 3 & 4
Step 2
Step 3
™ Dispenser to be free from defects in material and workmanship
Dispenser or
Regulator
Push Fitting
Step 5
Step 4