Direct Calling (Baby Call); Blocking Numbers; Network Services; Caller Display (Clip) - Gigaset DA611 Manual De Instrucciones

Selecting an emergency number
c
Lift the handset.
~
Enter the emergency number.
Emergency is indicated in the display.
Saving the emergency number
K
¢ ¢
Security Emergency
Q O
... Enter the emergency number and confirm with

Direct calling (baby call)

When direct calling is activated, the stored number is dialled by pressing
E
any key after lifting the handset (except for the keys
).
Activating direct calling
K
¢ ¢
Security Direct call
Q O
... Enter the direct calling number and confirm with
Direct calling is activated and indicated in the display.
Deactivating direct calling
K
Press the menu key.

Blocking numbers

You can block phone calls to specific dialling codes (e.g. chargeable
codes), max. 3 numbers with 5 digits each.
K
¢ ¢
Security Call block
s
Select Call block 1 (or 2 or 3) and confirm with
Q O
... Enter the call block number and confirm with

Network services

Public telephone systems offer you – in some cases only on request – a
range of helpful, additional services (e. g. call forwarding, callback when
busy, withheld number, etc.). These services can be selected using spec-
ified key combinations, of which your network provider will notify you.

Caller display (CLIP)

If the caller display service is activated, an incoming call is shown on the
display with the number and saved in the call list.
Prerequisite: The network provider supports the following service fea-
tures and the number transfer is not withheld by the caller:
u CLI (Calling Line Identification): The caller's number is transferred.
u CLIP (Calling Line Identification Presentation): The caller's number is
displayed.
You can transfer this number to the phonebook and edit it (
If you have saved the local dialling code (
same dialling code is automatically only displayed as the number with-
out the dialling code.
12
[
.
@ D
, and
[
.
[
.
[
.
£
£
page 8).
page 12), a call with the

Recall key

In public telephone systems the recall key (flash) is required for the use
of various additional services; e.g. for "callback when busy".
If necessary, the flash time on your telephone must be adjusted to the
requirements of the telephone system (

Setting up of dialling code

If necessary you can change the default setting for the area code for your
connection which is saved in the telephone. The number saved here is
then used to display only the number of the person calling without area
code in the call lists, provided that they have the same area code.
K
¢ ¢
Phone setup Area code
The default number is displayed.
Q O
[
... Enter the new area code (max. 6 digits) and confirm with
.

Operation on a PABX

Special functions/Recall key

H
During an external call, you can make an enquiry or forward the call. To
do this, press the recall key
on your PABX. To set the recall key, the telephone's flash time must be set
consistently with your PABX. Please refer to the operating instructions
for your PABX.

Changing the dialling mode/flash time

The telephone supports the following dialling modes:
u Tone dialling
u Pulse dialling
Depending on your PABX, you may need to change your phone's dialling
mode or the flash time. (Default setting: Tone dialling)
Changing the dialling mode
K
¢ ¢
Phone setup Dial mode
q
Select Tone or Pulse and confirm with
Changing the flash time
You can change the flash time if the dialling mode is set to tone dialling
(see above) (default setting 90 ms).
K
¢ ¢
Phone setup Flash time
q
Select flash time, the following values are available:
90, 120, 270, 375, 600 ms and confirm with
Temporary switch to tone dialling in "Pulse" position
To use functions that require tone dialling (e.g. remote control of
answering machine), you can set the telephone to tone dialling for the
duration of the call.
After the connection is established:
+
Press the star key.
After the connection is terminated, the setting reverts to pulse dialling.
£
page 12).
. The subsequent procedure depends
[
.
[
.
el en es it pt