Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Setting dialling prefixes
If your phone is connected to a PABX, you may have to use a dialling pre-
fix to make external calls. You can save up to three prefixes in your tele-
phone.
If a dialling prefix is recognised during dialling, a dialling pause will auto-
£
matically be applied. You can adjust the time of the dialling pause if nec-
essary (
page 13).
K
¢
¢
Phone setup
PABX code
The current setting is displayed.
Q
O
...
Enter the dialling prefix (1 to 3 digits) and confirm with
Use the control key to switch between the dialling prefixes:
t s
Press the control key up/downwards in order to jump left/
right
Other settings
n addition to the options described in section Adjusting the tele-
£
I
phone (
page 10), you can perform further settings with the help of
Feature codes (e.g. reset the factory settings). These are summarised in
the following table.
Default settings are displayed in bold. If there is no bold value for a set-
ting, the presetting is country-dependent.
K
Press the menu key and 1.
~
[
Enter the key sequence for the Feature code and confirm
with
.
Key
Value
sequence
02
0
1 s
1
3 s
2
6 s
25
0
Restores all settings to the factory settings
1
Deletes the contents of all programmable direct dial keys
2
Deletes PABX codes
3
Restores all network service codes
4
Deletes all stored numbers (not phonebook)
50
0
Time display off
1
24 hour format
2
12 hour format
57
0
Deactivate
1
500 ms/500 ms
2
30 ms/70 ms
70
0
Deactivate
1
Activate
83
0
Deactivate
1
Activate
2
Automatic
el en es it pt
[
Description
Sets the length of the pause that
can be inserted with the pause key
Sets the time format
Interval for the LED (hands-free
key) on incoming call
Eliminates click tone at the begin-
ning or end of ringer.
If network transmits only a very
short ringer impuls, the click tone
can be prevented by deactivating
(setting 0) the setting.
Withholds the first ringer. With this
setting, it is possible to determine,
if an incoming call comes from a VIP
number, and to select a VIP ring
tone instead of the normal ring
tone.
Key
Value
sequence
88
0-9
Settings 0-9
0 = minimum contrast
5 = default setting
9 = maximum contrast
91
0
1.5 : 1
1
2 : 1
92
0
85 / 85 ms
1
85 / 110 ms
2
85 / 140 ms
.
3
110 / 110 ms
4
70 / 70 ms
#2
0
Activate
1
Deactivate
0
Ringer
#4
1
AC
#6
0-9
Seconds
Settings 0 (3s) - 9 (12s)
Default setting: 5 (8s)
Standard characters
The following characters can be entered using the keypad:
Standard
Key
1x
2x
3x 4x 5x 6x 7x 8x 9x 10x 11x 12x 13x 14x
*)
1
€
2
A
B
C
3
D
E
F
4
G
H
I
5
J
K
L
L
M
N
O
M
P
Q
R
N
T
U
V
O
W
X
Y
Q
.
,
?
+
*
/
(
$
#
@
\
*) Space
Description
Sets the contrast of the display.
Sets the pulse ratio for pulse dial-
ling
Sets signal time/signal pause for
tone dialling
Updates time automatically
according to CLIP information
Start signal for CLIP recognition.
If CLIP does not function with the
default setting 0, select setting
"AC".
Time for termination of an incom-
ing call. For example: setting value
is 5, means 8 seconds.
£
$
¥
¤
2
Ä
Á
À
Â
Ã
Ç
3
Ë
É
È
Ê
4
Ï
Í
Ì
Î
5
6
Ö
Ñ
Ó
Ò
Ô
Õ
S
7
8
Ü
Ú
Ù
Û
Z
9
Ÿ
Ý
Æ
Ø
Å
!
0
+
-
:
¿
¡
)
<
=
>
%
&
§
"
'
;
_
13
Publicidad
Capítulos
Tabla de contenido
