Bell & Ross BR 03 Manual De Instrucciones página 3

BR 03 PATROUILLE DE FRANCE
BR-CAL.104 quartz
Movement : quartz. Calibre BR-CAL.104.
and date. Chronograph: 30-minute and 60-second counters. Time-setting with hacking
Case
function. : 42 mm in diameter. Black DLC (Diamond Like Carbon) steel finish.
GENERAL USE
Starting the watch. The watch starts running once the battery has been fitted.
Setting the time
. Pull the crown out to position 2. The seconds hand will stop,
enabling you to set the time to the nearest second. Set the time by rotating the crown
USING THE CHRONOGRAPH
The chronograph function can measure time in minutes and seconds.
Measuring a time period
First press of Pusher P1: sets off the time measurement.
Second press of Pusher P1: stops the time measurement.
Third press of Pusher P2: stops and resets the chronograph.
Measuring a time period with an interruption
First press of Pusher P1: sets off the time measurement.
Second press of Pusher P1: stops the time measurement.
Third press of Pusher P1: restarts the time measurement.
This allows one or more time intervals to be subtracted from the total time measured.
Fourth press of Pusher P1: stops the time measurement.
Fifth press of Pusher P2: stops and resets the chronograph.
A
B
C
D
E
F
(x4)
G
STRAP MOUNTING
Attachments (G) with no visible screws
A spring bar is used to fit the strap to the case attach-
ments. This bar must be removed carefully using the
appropriate tool provided with the watch in the box.
IMPORTANT
* Quickset date setting. As with all watches with a date function, quickset date
setting (crown in position 1) MUST NOT UNDER ANY CIRCUMSTANCES be carried out
between the times of 9 P .M. (21:00) and 3 A.M. (03:00).
Water resistance. Once the watch is set, to ensure perfect water resistance, push
the crown back to position 0. Never operate the crown underwater.
Note: The 4 slotted screws (D) mount the bezel to the case and ensure the water
resistance of the watch. To benefit from the Bell & Ross warranty, these screws must
never be unscrewed.
Functions : hours, minutes, small seconds
P
0 1 2
I
P
H
in the required direction.
crown out to position 1 and set the date by rotating the crown clockwise. Slow setting
(crown in position 2): to ensure the date changes at midnight rather than noon, it is
recommended you set the date by adjusting the hands of the watch. Pull the crown
out to position 2 and turn the hands until the date changes. Then set the precise time.
Measuring split times.
1 press of Pusher P1: sets off the time measurement.
st
2 press of Pusher P2: the chronometer hands stop, but the measurement continues
nd
in the background.
3 rd press of Pusher P2: restarts the time measurement. The chronometer hands move forwards
quickly to the actual time which has elapsed since the start of the first time measurement.
4 press of Pusher P1: stops the time measurement.
th
5 press of Pusher P2: stops and resets the chronograph.
th
1
A. Minute hand
B. Chronograph 60-second hand
C. Hour hand
D. Chronograph 30-minute counter
E. Seconds hand
F.
Case attachment screw
G. Strap attachment
H. Date
I.
Crown
2
P . Pusher 1.
1
P . Pusher 2.
2
1.
Set the date (rotate clockwise)
2. Set the time (rotate in either direction)
MAINTENANCE
After being immersed in seawater, it is recommended to carefully rinse off the watch
and strap with fresh water. It is also recommended to have the water resistance of
your watch checked every two years.
BELL & ROSS INTERNATIONAL WARRANTY
To benefit from your 2-year international warranty, your card must be activated at the
time of purchase by your approved Bell & Ross point of sale, and presented every time
an operation is performed. You can now access the digital version of this card and all
the information relating to your watch by scanning the QR code or visiting:
www.bellross.com/warranty.
To ensure a service that meets the brand's exacting standards, any servicing of your
watch must be carried out by the Bell & Ross service centre or a watchmaker approved
by Bell & Ross. The warranty does not, however, include:
. Any damage caused by accidents or by inappropriate or improper use of the watch
(e.g. violent impacts, crushing, rough handling of the clasp).
. Any damage caused by repair or disassembly operations carried out by a retailer or
after-sales service centre not approved by Bell & Ross.
. The consequences of the watch and bracelet/strap ageing and normal wear and tear.
3
Setting the date . Quickset * (crown in position 1): pull the
(NEVER UNSCREW)