Sanremo SR50 Libro De Instrucciones página 10

Warnings regarding operation
• Do not leave the appliances turned ON without
coffee in the hopper.
• In the grinder-doser version, avoid pulling the
doserlever partially, always pull it all the way.
Safety devices
THERMAL OVERLOAD PROTECTION
The appliance's motor is protected against over-
heating resulting from overcurrents by a thermal
overload protection which, when tripped, cuts off
the power supply to the motor. Should the protec-
tion trip as a result of anomalous operation, such as
the grinding blades jamming, the appliance must
be turned off using the on-off switch, UNPLUGGED
FROM THE MAINS, AND SKILLED TECHNICAL PER-
SONNEL CONTACTED. NEVER PERFORM ANY
WORK ON THE APPLIANCE WHILE IT IS ATTACHED
TO THE MAINS, TO AVOID THE RISK THAT MOTOR
TURNS ON SUDDENLY.
If the appliance overheats as a result of the motor
stopping, allow the appliance to cool down before
performing any repair work.
SAFETY SCREWS
The hopper must always be attached to the upper
grinding blade hol-der using the relevant screw,
which must not be removed by the user under any
circumstances.
In order to prevent the adjustment disk from being
removed - which would make the rotating parts
accessible - there is a safety screw on the actual
disk: said screw must be positioned in whichever of
the two holes on the disk enables the wider and
most suitable range of grinding adjustment, and
must not be removed by the user under any cir-
cumstances.
COFFEE OUTLET GUARD
The coffee outlet guard must always be fixed to the
doser using the relevant screws, wich must never
be removed by the user.
The removal of the coffee outlet guard can be done
by skilled technical personnel only after disconnect-
ing the appliance from the power supply by unplug-
ging. Before reconnecting the appliance to the pow-
er supply, fix the safety device to the doser by the
relevant screws.
Noise level
EEC Countries:
The maximal noise emission of our grinder-dosers
(valued as acoustic power) is 81 dB(A), measured
in ISO 3741 reverberating chamber, according to EN
60704-1:1998 and EN 60704-3:1996.
The daily personal noise exposure of a worker, due
only to an appliance's limit operation of 240 min.
per eight hours, is 78 dB(A), according to ED
86/188/EEC and ED 200311 0/EEC. Therefore dur-
ing he appliance's normal operation, no pro-visions
are to be taken in order to prevent such risks aris-
ing or likely to arise from noise exposure at work
(articles 3-8 of ED 2003/10/EEC).
Maintenance
It is essential to check the state of the supply cable
and plug periodically.
IN THE EVENT THE SUPPLY CABLE OR PLUG ARE
DAMAGED, CALL IN SKILLED TECHNICAL PERSONNEL
TO REPLACE THEM, THIS TO PREVENT ANY RISK.
IN CE-CERTIFIED APPLIANCES A SPECIAL TOOL IS
REQUIRED TO OPEN THE BASE PLATE TO GET AT
THE CABLE.
It is recommended to use original spare parts only.
In order to assure the lasting efficiency of the appli-
ance, skilled technical personnel must be called in
to perform periodical maintenance, including
detailed checks of the state of those components
subject to wear.
The state of the grinding blades must be checked
periodically. Keeping the grinding blades in an
excellent state assures high-quality grinding, result-
ing in greater productivity and limited overheating.
Cleaning the appliance
DISCONNECT THE APPLIANCE'S POWER SUPPLY
BY UNPLUGGING IT BEFORE CLEANING.
THE APPLIANCE MUST NOT BE CLEANED USING
WATER JETS.
18
Do not install the appliance in rooms where water
jets are used for cleaning.
THE APPLIANCE MUST BE CLEANED PERIODICALLY
BY SKILLED TECHNICAL PERSONNEL ONLY.
Use perfectly clean, disinfected cloths or brushes for
cleaning.
Do not use abrasive products as these are liable to
take the sheen off shiny parts.
Hopper
Wash the hopper once it has been removed from
the appliance (unscrewing the relevant fastening
screw), using neutral soap and water, rinse abun-
dantly with lukewarm water and dry thoroughly.
It is advisable to clean the hopper periodically.
Once the hopper has been cleaned, it must be
attached to the upper grinding blade holder using
the relevant screw.
Grinding system
Remove the safety screw which prevents the adjust-
ment disk from being removed. Unscrew the
adjustment disk by turning it clockwise. Having
removed the upper grinding blade holder, clean the
grinding blades, threads and the entire grinding sys-
tem thoroughly using a clean brush and cloth.
Having refitted the upper grinding blade holder in
the relevant slot, screw the adjustment disk back
on, put the self-locking screw back in whichever of
the two holes on the disk enables the best adjust-
ment and, having refitted the hopper and secured,
adjust the grinding as required.
Doser
Having discharged the ground coffee, clean the
doser's star unit with a clean brush, expelling the
material removed by pulling the doser lever.
Use a dry cloth to thoroughly clean the outlet of the
ground coffee on the bottom of the doser.
When a more thorough cleaning is required, the
operation must be performed only by skilled tech-
nical personell, after disconnecting the appliance
from the power supply.
Warranty
Every purchased appliance (keep the receipt,
invoice, and delivery note) is covered by a statu-
tory guarantee. This warranty envisages the
replacement free of charge of parts that are
shown to the service centre or manufacture's sat-
isfaction to be defective due to faulty materials or
workmanship and providing that the appliance
has not been misused or tampered with by
unauthorised persons or persons using incorrect
components or techniques.
Any defective part shall be returned to the manu-
facturer.
19