Publicidad
Idiomas disponibles
Idiomas disponibles
8
FLUSHING INSTRUCTIONS (after faucet installation)
IMPORTANT: Pipe chips, sand, stones and other solids found in new and renovated
plumbing can damage the sealing surfaces of the cartridge and cause leaks. To avoid
damages, DO NOT TURN ON SUPPLY VALVES until instructed below.
1. Unscrew aerator.
2. Turn faucet on in the full cold position (handle pointing to the right) and
turn on the cold supply for 15 seconds.
3. Without turning the faucet off, turn the handle to the full hot position
(handle pointing to the left) and turn on the hot supply for 15 seconds.
4. Without turning the faucet off, turn the handle to the mid/mix position
(handle pointing toward you) and turn on the spray for 15 seconds.
5. Shut off faucet.
6. Replace aerator and check system below sink for leaks.
Your new Moen faucet is now ready for normal use.
CARE INSTRUCTIONS
All that is needed to clean your faucet is a soft damp cloth. Moen does not recommend
the use of scour pads, cleansers or chemicals. The abrasive nature of these substances
could damage the faucet's finish. A non abrasive car wax will help to protect the finish.
TROUBLE SHOOTING
• REVERSED HOT AND COLD POSITIONS
HELPFUL HINTS: IT IS NOT NECESSARY TO SHUT
OFF WATER SUPPLIES. HANDLE SCREW REQUIRES A
7/64" HEX KEY ALLEN WRENCH.
1. Remove handle cap (1), temperature indicator (2),
handle screw (3), handle body (4) or (5) and
parts 6-8 in drawing on page 1. NOTE: Dome
and pivot retainer assembly (6) unscrews count-
er clockwise as one unit.
2. Turn cartridge stem around so that the
notch is turned one half turn or 180°.
3. Reinstall as follows: Be sure D-washer (14) is
present on cartridge stem, and raised edge of pivot
stop (9) faces front. Note orientation of handle
adapter & connector assembly (8) in the exploded
WARRANTY
Moen products have been manufactured under the highest standards of quality and workmanship. Moen warrants
to the original consumer purchaser for as long as the original consumer purchaser owns their home (the "Warranty
Period" for homeowners), that this faucet will be leak and drip-free during normal use and all parts and finishes of this
faucet will be free from defects in material and manufacturing workmanship. All other purchasers (including purchasers
for industrial, commercial and business use) are warranted for a period of 5 years from the original date of purchase
(the "Warranty Period" for non-homeowners).
If this faucet should ever develop a leak or drip during the Warranty Period, Moen will FREE OF CHARGE provide
the parts necessary to put the faucet back in good working condition and will replace FREE OF CHARGE, any part or
finish that proves defective in material and manufacturing workmanship, under normal installation, use and service.
Replacement parts may be obtained by calling 1-800-289-6636, or by writing to the address shown below. Proof of
purchase (original sales receipt) from the original consumer purchaser must accompany all warranty claims. Defects
or damage caused by the use of other than genuine Moen parts are not covered by this warranty. This warranty is
applicable only to faucets purchased after December 1995 and shall be effective from the date of purchase as
shown on purchaser's receipt.
This warranty is extensive in that it covers replacement of all defective parts and finishes. However, damage due
to installation error, product abuse, product misuse, or use of cleaners containing abrasives, alcohol or other organic
solvents, whether performed by a contractor, service company, or yourself, are excluded from this warranty. Moen will
not be responsible for labor charges and/or damage incurred in installation, repair or replacement, nor for any indirect,
incidental or consequential damages, losses, injury or costs of any nature relating to this faucet. Except as provided by
law, this warranty is in lieu of and excludes all other warranties, conditions and guarantees, whether expressed or
implied, statutory or otherwise, including without restriction those of merchantability or of fitness for use.
Some states, provinces and nations do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights
and you may also have other rights which vary from state to state, province to province, nation to nation. Moen will
advise you of the procedure to follow in making warranty claims. Simply write to Moen Incorporated using the address
below. Explain the defect and include proof of purchase and your name, address, area code and telephone number.
3
Moen Incorporated 25300 Al Moen Drive, North Olmsted, OH 44070-8022 U.S.A. in Canada: Moen Inc. 2816 Bristol Circle, Oakville, Ontario L6H5S7
TURN STEM
1/2 TURN
NOTCHED FLAT
9
ON STEM
Questions,
Comments?
Call Moen!
1 (800) BUY-MOEN
In the U.S., call our toll free Helpline number for answers
to any product installation or warranty questions.
Toronto: 905-829-3400;
Rest of Canada: 1-800-465-6130
(84) 88-08-26, 88-08-27,
PLEASE HAVE THE FOLLOWING INFORMATION
AVAILABLE WHEN CALLING OUR MOEN HELPLINE:
• Faucet Model Number
• Faucet Finish
• Date and Location of Faucet Purchase
view. Completely tighten cartridge screw (7) to prevent self closure
of faucet. Thread on dome and pivot retainer assembly (6) clockwise
until hand tight. Reinstall handle body (4) or (5), handle screw (3),
temperature indicator (2) and handle cap (1).
• IRREGULAR WATER FLOW
Remove the aerator from the spout and
flush thoroughly, then reinstall.
• LOW WATER FLOW
Moen aerators comply with government regulations to
save both water and energy. Your old faucet may not
have met these standards.
• LEAKS FROM TOP OR BOTTOM OF SPOUT HUB
Use replacement spout seal kit, replace and reassemble
following instructions included with kit #117.
• DRIPS FROM SPOUT/LEAKS THROUGH HANDLE
Replace Moen 1225 Cartridge with new one.
Instructions are included with the 1225 cartridge.
CONSUMER INFORMATION
Faucets made of leaded brass alloys may contribute small amounts of
lead to water that is allowed to stand in contact with the brass. The
amount of lead contributed by any faucet is highest when the faucet is
new. The following steps may reduce potential exposure to lead from
faucets and other parts of the plumbing system:
• Always run the water for a few seconds
prior to use for drinking or cooking
• Use only cold water for drinking or cooking
• If you wish to flush the entire plumbing system of water
that has been standing in the pipes or other fittings, run the
cold water until the temperature of the water drops, indicating
water coming from the outside main
• If you are concerned about lead in your water, have
your water tested by a certified laboratory in your area
This faucet has been tested under actual operating conditions
and complies with flow restrictions for water usage as set by the
Federal Trade Commission.
[289 - 6636]
In Canada:
In Mexico:
o 91-800-84-345
INS106E
Publicidad
