Spraying Instructions - Hudson 2204 Guia De Inicio Rapido

FEATURES
WITH 5 LIQUID SPRAY SETTINGS AND 2 GRANULAR SETTINGS,
THE WET/DRY SPRAYER CAN COVER A VARIETY OF SPRAYING JOBS.
NO MIXING NO MEASURING NO CONVERSION
ADD PRODUCT, SET KNOB AND SPRAY!
LIQUID MEASUREMENTS (per gallon of water)
1 TABLESPOON (tbsp) = 3 TEASPOONS (tsp) or 15 MILLILITERS
2 TABLESPOONS = 1 FLUID OUNCE (fl oz) or 30 MILLILITERS
1 CUP = 16 tbsp or 8 fl oz or 240 MILLILITERS
1 PINT = 16 fl oz (or 2 cups) or .5 LITER
1 QUART = 32 fl oz (or 2 pints) or 1 LITER
GRANULAR COVERAGE
1-1/4 POUNDS....UP TO 1,000 SQUARE FEET
2 POUNDS....UP TO 1,600 SQUARE FEET
*Coverage is estimated and may vary with working water pressure
and walking speed.
AREA COVERAGE
2 ft x 50 ft 4 ft x 250 ft
4 ft x 25 ft 5 ft x 200 ft
100 sq ft = 1000 sq ft =
5 ft x 20 ft 10 ft x 100 ft
10 ft x 10 ft 20 ft x 50 ft

SPRAYING INSTRUCTIONS

1. Select the desired Spray Pattern Setting on the front spray
nozzle by rotating the dial. The setting that you choose will
always be on the top or "12 o'clock" position.
Do not turn water on when adjusting the spray nozzle.
See spray pattern detail picture.
2. Be sure the Product Control Knob is set at the measurement
indicated by the product label.
3. When you are ready to spray, hold the contoured handle in
either your right or left hand and slide the thumb switch back to
the water "ON" position.
4. You are now spraying a properly diluted solution. To stop
spraying, simply slide the thumb switch forward to the water
"OFF" position. The valve will automatically snap in place and
stop the flow application.
5. After spraying, clean your sprayer according to the following
instructions. Never leave unused product in the jar for an
extended period of time.
PRODUCT CONTROL KNOB
WET (LIQUID) SETTINGS
The control settings refer to the amount of concentrate of
liquid the sprayer will mix into each gallon of water.
This is a multi-function precision sprayer–follow directions
exactly
EXACT SETTING = PRECISION SPRAYING
Use the following liquid A full sprayer jar will make
settings on the sprayer: this many gallons:
1 tsp = 5 mL 192.0
1.5 tsp = 7.5 mL 128.0
2 tsp = 10 mL 96.0
1 tbsp (3 tsp) = 15 mL 64.0
4 tsp = 20 mL 48.0
PRODUCT CONTROL KNOB
DRY SETTINGS
The control settings refer to the type of granules the sprayer
will mix with the water.
The flower and vegetable setting can be used to spray lawn food.
Ratio of Spray: Flower & Vegetable = 9:1
The acid loving setting can be used to spray rose food.
Ratio of Spray: Acid Loving = 21:1
This is a multi-function precision sprayer–
follow directions exactly
EXACT SETTING = PRECISION SPRAYING
FILLING INSTRUCTIONS
1. Unscrew plastic jar from sprayer.
2. Place plastic jar on flat surface. Pour the approximate amount of product you
need for one application.
3. Attach supply tube to sprayer head if spraying a liquid product. Do not use
supply tube when spraying granules.
4. Replace sprayer head on the jar and attach to your garden hose with the swivel
hose connector.
5. Make sure the water control thumb switch is in the forward or "OFF" position
and the product knob is in the "OFF" position. Turn the water on to the garden
hose.
6. Rotate the control knob so that the indicator points to the proper setting for the
type of spray and dosage you are using.
JAR MEASUREMENTS
LIQUID FEEDER
Liquid ounce
measurements
for direct product
application.
Product is poured
straight into the
jar and then
sprayed.
SPRAY PATTERN
Material always exits from top setting.
DETAIL
Bullet spray for trees, high places and
tough rinse jobs.
Gentle shower for flowers, delicate
shrubs and roses.
Rotate for spray selection.
(Water should be off when
rotating spray head.) Flat spray for lawns and large areas.
GRANULAR FEEDER
This jar holds up to
2 lbs of granules.
Product is poured
straight into the jar
and then sprayed.